Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0115  Engine Coolant Temperature Circuit Malfunction  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor, whose resistance value varies according to the engine coolant temperature, is built into the engine coolant temperature sensor. The connection between the engine coolant temperature sensor and the ECM is the same as that of the intake air temperature sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0115 Engine Coolant Temperature Circuit Malfunction An open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1-trip detection logic).
·

Open or short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored
P0117 Engine Coolant Temperature Circuit Low Input A short in the engine coolant temperature sensor circuit for 0.5 seconds (1-trip detection logic).
·

Short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored
P0118 Engine Coolant Temperature Circuit High Input An open in the engine coolant temperature sensor circuit for 0.5 seconds (1-trip detection logic).
·

Open in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the engine coolant temperature using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit

WIRING DIAGRAM

A162760
0.406,1.854 0.969,2.063 0.563,0.208 10 false C17 2.448,1.229 2.688,1.438 0.24,0.208 10 false 1 2.448,0.625 2.688,0.833 0.24,0.208 10 false 2 5.25,0.625 5.49,0.833 0.24,0.208 10 false 18 6.198,0.188 6.531,0.396 0.333,0.208 10 false 5 V 6.292,0.583 6.531,0.792 0.24,0.208 10 false R 5.521,0.625 5.906,0.833 0.385,0.208 10 false THW 5.521,1.24 5.99,1.448 0.469,0.208 10 false ETHW 5.969,2.24 6.396,2.448 0.427,0.208 10 false C95 5.969,2.396 6.396,2.604 0.427,0.208 10 false ECM 5.25,1.25 5.49,1.458 0.24,0.208 10 false 17 0.406,2.031 2.406,2.552 2,0.521 10 false Engine Coolant Temperature Sensor

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

e.

Read the value displayed on the tester.

Result:
Result Proceed to
Temperature displayed is -40°C (-40°F) A
Temperature displayed is 140°C (284°F) B
Temperature displayed is between 80°C and 100°C (176°F and 212°F) C


HINT:
·

If there is an open circuit, the intelligent tester indicates -40°C (-40°F).

·

If there is a short circuit, the intelligent tester indicates 140°C (284°F).





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
A208643
0.688,2.792 1.052,3.021 0.365,0.229 0.719,0.271 1.083,0.49 0.365,0.219 10 false *1 2.615,0.271 2.885,0.49 0.271,0.219 10 false *2 0.906,2.229 1.188,2.448 0.281,0.219 10 false *a 0.75,2.833 1.115,3.052 0.365,0.219 10 false C17 2.417,1 2.781,1.219 0.365,0.219 10 false THW 2.417,1.469 2.917,1.688 0.5,0.219 10 false ETHW
*1 Engine Coolant Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor)


Confirm that there is a good connection at the engine coolant temperature sensor.


b.

Disconnect the engine coolant temperature sensor connector.


c.

Connect terminals 1 and 2 of the wire harness connector for the engine coolant temperature sensor.


d.

Connect the intelligent tester to the DLC3.


e.

Turn the ignition switch to ON.


f.

Turn the tester on.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

h.

Read the value displayed on the tester.

Standard value:

140°C (284°F)



i.

Reconnect the engine coolant temperature sensor connector.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C17-2 - C95-18 (THW) Always Below 1 Ω
C17-1 - C95-17 (ETHW) Always Below 1 Ω



d.

Reconnect the engine coolant temperature sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A211723
0.688,0.292 1.031,0.479 0.344,0.188 10 false *1 2.583,0.281 2.927,0.521 0.344,0.24 10 false *2 2.417,1 2.906,1.24 0.49,0.24 10 false THW 2.438,1.458 2.927,1.698 0.49,0.24 10 false ETHW
*1 Engine Coolant Temperature Sensor
*2 ECM


Disconnect the engine coolant temperature sensor connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

f.

Read the value displayed on the tester.

Standard value:

-40°C (-40°F)



g.

Reconnect the engine coolant temperature sensor connector.


Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C17-2 or C95-18 (THW) - Body ground Always 10 kΩ or higher



d.

Reconnect the engine coolant temperature sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)