Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0300  Random / Multiple Cylinder Misfire Detected  P0301  Cylinder 1 Misfire Detected  P0302  Cylinder 2 Misfire Detected  P0303  Cylinder 3 Misfire Detected  P0304  Cylinder 4 Misfire Detected  


DESCRIPTION

A093767C03
2.302,0.906 2.49,1.073 0.188,0.167 10 false *3 0.531,0.219 0.698,0.385 0.167,0.167 10 false *1 0.531,1.729 0.708,1.885 0.177,0.156 10 false *2
*1 Camshaft Position Sensor
*2 Crankshaft Position Sensor
*3 ECM


When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emissions levels. High concentrations of HC can also cause increases in the Three-way Catalytic Converter (TWC) temperature, which may cause damage to the Three-way Catalytic Converter (TWC). To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the Three-way Catalytic Converter (TWC) reaches the point of thermal degradation, the MIL blinks. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted as when the crankshaft rotation speed variations exceed predetermined thresholds.

If the misfire rate exceeds the threshold, the ECM illuminates the MIL and stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0300 Random / Multiple Cylinder Misfire Detected Simultaneous misfiring of several cylinders occurs and one of the following conditions below is detected (2 trip detection logic):
·

High temperature misfire occurs in the Three-way Catalytic Converter (TWC) (MIL blinks).

·

Catalyst deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Air induction system

·

ECM


Comes on/blinks*
*: The MIL flashes when catalyst-damaging misfire is detected.
DTC stored
P0301 Cylinder 1 Misfire Detected Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection logic):
·

High temperature misfire occurs in the Three-way Catalytic Converter (TWC) (MIL blinks).

·

Catalyst deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Air induction system

·

ECM


Comes on/blinks*
*: The MIL flashes when catalyst-damaging misfire is detected.
DTC stored
P0302 Cylinder 2 Misfire Detected Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection logic):
·

High temperature misfire occurs in the Three-way Catalytic Converter (TWC) (MIL blinks).

·

Catalyst deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Air induction system

·

ECM


Comes on/blinks*
*: The MIL flashes when catalyst-damaging misfire is detected.
DTC stored
P0303 Cylinder 3 Misfire Detected Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection logic):
·

High temperature misfire occurs in the Three-way Catalytic Converter (TWC) (MIL blinks).

·

Catalyst deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Air induction system

·

ECM


Comes on/blinks*
*: The MIL flashes when catalyst-damaging misfire is detected.
DTC stored
P0304 Cylinder 4 Misfire Detected Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection logic):
·

High temperature misfire occurs in the Three-way Catalytic Converter (TWC) (MIL blinks).

·

Catalyst deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Air induction system

·

ECM


Comes on/blinks*
*: The MIL flashes when catalyst-damaging misfire is detected.
DTC stored

When multiple DTCs for misfiring cylinders are stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when the following condition, which could cause catalyst deterioration, is detected (2 trip detection logic).

·

An excessive misfiring rate (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.


The ECM flashes the MIL immediately when the following condition, which could cause three-way catalytic converter damage, is detected. Also, the ECM stores a DTC when the following condition is detected (2 trip detection logic).

·

A sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.


MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor and camshaft position sensor
Required Sensors/Components (Related) Engine coolant temperature, intake air temperature sensor and mass air flow meter
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Misfire
Intake air temperature Higher than -10°C (14°F)
Either of following conditions (a) or (b) met -
(a) Engine coolant temperature at engine start Higher than -7°C (19°F)
(b) Engine coolant temperature Higher than 20°C (68°F)

Monitor Period of Emissions-related Misfire
Duration 1000 crankshaft revolutions x 4

Monitor Period of Catalyst-damaging Misfire (MIL Blinks)
Duration 200 crankshaft revolutions x 3

WIRING DIAGRAM

A247769E12
6.146,4.083 6.667,4.333 0.521,0.25 10 false ECM 5.656,3.104 6.135,3.344 0.479,0.24 10 false E01 5.667,3.521 6.01,3.719 0.344,0.198 10 false E02 5.656,2.406 6.021,2.656 0.365,0.25 10 false #40 5.656,1.74 6.115,2.052 0.458,0.313 10 false #30 5.656,1.063 5.979,1.25 0.323,0.188 10 false #20 5.656,0.375 6.063,0.573 0.406,0.198 10 false #10 4.104,0.375 4.302,0.573 0.198,0.198 10 false 1 4.729,0.375 4.99,0.604 0.26,0.229 10 false 2 5.406,3.438 5.594,3.625 0.188,0.188 10 false 6 3.865,0.563 4.271,0.792 0.406,0.229 10 false C65 5.406,3.01 5.5,3.156 0.094,0.146 10 false 7 5.406,2.333 5.615,2.552 0.208,0.219 10 false 1 5.396,1.646 5.563,1.833 0.167,0.188 10 false 2 5.406,0.969 5.552,1.135 0.146,0.167 10 false 5 5.406,0.281 5.635,0.49 0.229,0.208 10 false 6 5.323,0.458 5.698,0.646 0.375,0.188 10 false C76 5.323,1.146 5.688,1.365 0.365,0.219 10 false C76 5.323,1.823 5.688,2.021 0.365,0.198 10 false C76 5.323,2.51 5.74,2.729 0.417,0.219 10 false C76 5.323,3.198 5.698,3.385 0.375,0.188 10 false C75 5.323,3.615 5.688,3.865 0.365,0.25 10 false C75 3.865,1.25 4.146,1.427 0.281,0.177 10 false C2 3.865,1.948 4.292,2.146 0.427,0.198 10 false C66 3.865,2.625 4.156,2.802 0.292,0.177 10 false C4 3.865,0.708 5.208,0.938 1.344,0.229 10 false No. 1 Fuel Injector 4.104,1.052 4.344,1.25 0.24,0.198 10 false 1 4.729,1.052 4.927,1.25 0.198,0.198 10 false 2 3.865,1.385 5.229,1.604 1.365,0.219 10 false No. 2 Fuel Injector 4.104,1.75 4.333,1.979 0.229,0.229 10 false 1 4.729,1.75 4.885,1.927 0.156,0.177 10 false 2 3.865,2.083 5.219,2.344 1.354,0.26 10 false No. 3 Fuel Injector 4.104,2.438 4.302,2.677 0.198,0.24 10 false 1 4.729,2.438 4.896,2.625 0.167,0.188 10 false 2 3.865,2.771 5.167,2.99 1.302,0.219 10 false No. 4 Fuel Injector 0.76,3.583 1.563,3.917 0.802,0.333 10 false Battery 0.625,2.667 1.135,2.896 0.51,0.229 10 false AM2 0.896,1.531 1.833,1.74 0.938,0.208 10 false Ignition Switch 1.698,0.594 2.073,0.813 0.375,0.219 10 false INJ 0.896,1.375 1.115,1.542 0.219,0.167 10 false G9 0.542,1.188 0.906,1.385 0.365,0.198 10 false IG2 0.531,1.74 0.99,1.969 0.458,0.229 10 false AM2 0.563,0.938 0.667,1.115 0.104,0.177 10 false 6 0.563,1.99 0.667,2.167 0.104,0.177 10 false 5

A247770E09
5.656,0.792 6.198,1.073 0.542,0.281 10 false IGT1 3.938,0.677 4.375,0.875 0.438,0.198 10 false IGT1 4.01,1.01 4.427,1.271 0.417,0.26 10 false IGF 3.615,0.667 3.99,0.854 0.375,0.188 10 false +B 3.604,1.01 4.031,1.219 0.427,0.208 10 false GND 5.656,2.188 6.323,2.604 0.667,0.417 10 false IGT2 5.656,3.563 6.115,3.823 0.458,0.26 10 false IGT3 5.656,4.969 6.104,5.281 0.448,0.313 10 false IGT4 5.656,5.729 6.042,5.938 0.385,0.208 10 false IGF1 6.156,6.188 6.51,6.417 0.354,0.229 10 false C75 6.156,6.354 6.677,6.635 0.521,0.281 10 false ECM 5.396,0.573 5.688,0.792 0.292,0.219 10 false 17 5.385,5.51 5.604,5.688 0.219,0.177 10 false 23 5.385,4.74 5.656,4.938 0.271,0.198 10 false 14 5.385,3.344 5.667,3.542 0.281,0.198 10 false 15 5.385,1.948 5.76,2.198 0.375,0.25 10 false 16 3.406,0.573 3.531,0.74 0.125,0.167 10 false 1 3.406,0.896 3.531,1.063 0.125,0.167 10 false 4 4.354,0.573 4.479,0.74 0.125,0.167 10 false 3 4.354,0.896 4.479,1.063 0.125,0.167 10 false 2 3.24,1.26 3.719,1.542 0.479,0.281 10 false C70 3.24,1.406 4.469,1.625 1.229,0.219 10 false No. 1 Ignition Coil 3.406,1.969 3.531,2.135 0.125,0.167 10 false 1 3.406,2.302 3.531,2.469 0.125,0.167 10 false 4 4.354,1.969 4.479,2.135 0.125,0.167 10 false 3 4.354,2.302 4.479,2.469 0.125,0.167 10 false 2 3.24,2.667 3.688,2.896 0.448,0.229 10 false C71 3.24,2.813 4.448,3.052 1.208,0.24 10 false No. 2 Ignition Coil 3.406,3.354 3.531,3.521 0.125,0.167 10 false 1 3.406,3.677 3.531,3.844 0.125,0.167 10 false 4 4.354,3.354 4.479,3.521 0.125,0.167 10 false 3 4.354,3.677 4.479,3.844 0.125,0.167 10 false 2 3.24,4.052 3.625,4.25 0.385,0.198 10 false C72 3.24,4.198 4.531,4.479 1.292,0.281 10 false No. 3 Ignition Coil 3.406,4.74 3.531,4.906 0.125,0.167 10 false 1 3.406,5.073 3.531,5.24 0.125,0.167 10 false 4 4.354,4.74 4.479,4.906 0.125,0.167 10 false 3 4.354,5.073 4.479,5.24 0.125,0.167 10 false 2 3.24,5.427 3.719,5.677 0.479,0.25 10 false C73 3.24,5.583 4.542,5.865 1.302,0.281 10 false No. 4 Ignition Coil 0.938,3.24 1.323,3.438 0.385,0.198 10 false G9 0.938,3.375 2.063,3.698 1.125,0.323 10 false Ignition Switch 0.552,1.979 0.802,2.135 0.25,0.156 10 false INJ 0.51,2.927 0.635,3.104 0.125,0.177 10 false 6 0.5,3.74 0.625,3.917 0.125,0.177 10 false 5 0.51,3.135 0.958,3.375 0.448,0.24 10 false IG2 0.51,3.521 0.927,3.729 0.417,0.208 10 false AM2 0.573,4.729 1.344,5.063 0.771,0.333 10 false AM2 0.719,6.052 1.448,6.313 0.729,0.26 10 false Battery 3.938,2.073 4.375,2.281 0.438,0.208 10 false IGT2 4.01,2.406 4.375,2.625 0.365,0.219 10 false IGF 3.604,2.073 3.906,2.281 0.302,0.208 10 false +B 3.604,2.406 4,2.604 0.396,0.198 10 false GND 3.948,3.448 4.427,3.667 0.479,0.219 10 false IGT3 4.021,3.781 4.417,4 0.396,0.219 10 false IGF 3.615,3.448 3.938,3.698 0.323,0.25 10 false +B 3.615,3.781 4.042,4.021 0.427,0.24 10 false GND 3.948,4.844 4.417,5.073 0.469,0.229 10 false IGT4 4.021,5.167 4.438,5.396 0.417,0.229 10 false IGF 3.615,4.833 3.99,5.063 0.375,0.229 10 false +B 3.615,5.167 4.042,5.417 0.427,0.25 10 false GND

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the intelligent tester on.

4.

Record the DTC(s) and freeze frame data.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

6.

Using the intelligent tester, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>CHECK MODE PROCEDURE).

7.

Read the misfire counts of each cylinder (cylinder No. 1 to No. 4) with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.

8.

Drive the vehicle several times with the conditions, such as engine speed and engine load, as shown in Misfire RPM and Misfire Load in the freeze frame data.

HINT:

In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below with the engine speed and engine load the same as Misfire RPM and Misfire Load in the freeze frame data.

Engine Speed Duration
Idling 7.0 minutes or more
1000 4.0 minutes or more
2000 2.0 minutes or more
3000 1.5 minutes or more


9.

Check whether misfires have occurred by checking DTCs and freeze frame data.

HINT:

Do not turn the ignition switch off until the stored DTCs and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTCs, freeze frame data and other data will be cleared.


10.

Record the DTCs, freeze frame data and misfire counts.

11.

Turn the ignition switch off and wait for at least 30 seconds.

12.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).


CAUTION / NOTICE / HINT

HINT:
·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.

·

If the misfiring still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors may be a cause of the problem:

1.

The fuel level is low.

2.

Improper fuel is being used.

3.

The spark plugs are dirty.


·

After finishing repairs, check that no misfires occur in each cylinder (cylinder No. 1, No. 2, No. 3 and No. 4).

·

Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after the repairs.

·

When one of Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +/-15%, the air-fuel ratio may be rich (-15% or less) or lean (+15% or more).

·

When Coolant Temp in the freeze frame data is below 75°C (167°F), the misfires may have occurred only while warming up the engine.

·

An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Result Proceed to
P0300, P0301, P0302, P0303 and/or P0304 is output A
P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output B


HINT:

If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.




A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.

Click hereEngine / Hybrid System>2TR-FE EMISSION CONTROL>EMISSION CONTROL SYSTEM(w/ Secondary Air Injection System)>ON-VEHICLE INSPECTION

OK:

PCV hose is connected correctly and is not damaged.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD)

NG

3.READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Misfire RPM and Misfire Load.

Powertrain > Engine > Data List
Tester Display
Misfire RPM
Misfire Load
50003 61 249,250

e.

Read and note the Misfire RPM and Misfire Load values.

HINT:

The Misfire RPM and Misfire Load values indicate the vehicle conditions under which misfire occurred.



Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING INTELLIGENT TESTER (MISFIRE COUNT)
4.READ VALUE USING INTELLIGENT TESTER (MISFIRE COUNT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.



e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Count, #2, #3 and #4.

Powertrain > Engine > Data List
Tester Display
Cylinder #1 Misfire Count
Cylinder #2 Misfire Count
Cylinder #3 Misfire Count
Cylinder #4 Misfire Count
50003 61 253,254,255,256

f.

Allow the engine to idle.


g.

Read the values for Cylinder #1 Misfire Count to Cylinder #4 Misfire Count displayed on the intelligent tester. If no misfire counts occur in any cylinders, perform the following procedures:

i.

Check Cylinder #1 Misfire Count to Cylinder #4 Misfire Count.


ii.

If misfire counts are still not displayed, perform procedures "A" and "B", and then check the misfire counts again.

Procedure A: Drive the vehicle while matching the vehicle conditions to the Misfire RPM and Misfire Load values noted in the "Read Value Using Intelligent Tester (Misfire RPM and Misfire Load)" procedure above.

Procedure B: Read Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or the DTCs output on the intelligent tester.

Result:
Result Proceed to
Most misfires occur in only 1 or 2 cylinders A
3 cylinders or more have equal misfire counts B


HINT:
·

If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.

·

If the freeze frame data's record of the engine coolant temperature is below 75°C (167°F), misfire may be detected only when the engine is cold.

·

If the freeze frame data's record of the Engine Run Time is less than 120 seconds, misfire may be detected immediately after the engine is started.






A

5.INSPECT SPARK PLUG

B

16.CHECK AIR INDUCTION SYSTEM
5.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK FOR SPARKS AND IGNITION

NG

6.CHECK FOR SPARKS AND IGNITION
a.

Perform a spark test.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION

CAUTION:

Always disconnect all the fuel injector connectors.


NOTICE:

Do not crank the engine for more than 2 seconds.


OK:

Spark jumps across electrode gap.



Result:
Proceed to
OK
NG



OK

7.CHECK CYLINDER COMPRESSION PRESSURE

NG

32.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
7.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>2TR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

8.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)
a.
A208644
0.417,0.667 0.74,0.906 0.323,0.24 0.417,0.969 0.74,1.208 0.323,0.24 0.417,1.271 0.74,1.51 0.323,0.24 0.417,1.573 0.74,1.813 0.323,0.24 0.083,0.063 0.417,0.354 0.333,0.292 10 false *a 0.458,0.708 0.792,1 0.333,0.292 10 false C65 0.49,1.01 0.823,1.302 0.333,0.292 10 false C2 0.458,1.313 0.792,1.604 0.333,0.292 10 false C66 0.5,1.615 0.833,1.906 0.333,0.292 10 false C4
*a Front view of wire harness connector
(to Fuel Injector Assembly)


Disconnect the fuel injector connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Cylinder Tester Connection Switch Condition Specified Condition
No. 1 C65-1 - Body ground Ignition switch ON 11 to 14 V
No. 2 C2-1 - Body ground Ignition switch ON 11 to 14 V
No. 3 C66-1 - Body ground Ignition switch ON 11 to 14 V
No. 4 C4-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)

NG

9.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)
a.

Disconnect the fuel injector connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Cylinder Tester Connection Condition Specified Condition
No. 1 C65-2 - Body ground Always 10 kΩ or higher
C65-2 - C76-6 (#10) Always Below 1 Ω
No. 2 C2-2 - Body ground Always 10 kΩ or higher
C2-2 - C76-5 (#20) Always Below 1 Ω
No. 3 C66-2 - Body ground Always 10 kΩ or higher
C66-2 - C76-2 (#30) Always Below 1 Ω
No. 4 C4-2 - Body ground Always 10 kΩ or higher
C4-2 - C76-1 (#40) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
a.

Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor].

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK AIR INDUCTION SYSTEM

NG

REPLACE FUEL INJECTOR ASSEMBLY

11.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage.

Click hereEngine / Hybrid System>2TR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leakage in air induction system.



Result:
Proceed to
OK
NG



OK

12.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

12.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

13.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)

NG

33.CHECK FUEL LINE
13.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 61 309

e.

Read Coolant Temp twice, when the engine is both cold and warmed up.

Standard:

With cold engine: Same as ambient air temperature.

With warm engine: Between 75°C and 100°C (167°F and 212°F).



Result:
Proceed to
OK
NG



OK

14.READ VALUE USING INTELLIGENT TESTER (MAF)

NG

14.READ VALUE USING INTELLIGENT TESTER (MAF)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.

Powertrain > Engine > Data List
Tester Display
MAF
Coolant Temp
50003 61 319,309

e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read MAF with the engine speed at 2500 rpm.

Standard:

Between 4 gm/s and 15 gm/s (shift lever: N; A/C: Off).



Result:
Proceed to
OK
NG



OK

15.CHECK VALVE TIMING

NG

27.CHECK HARNESS AND CONNECTOR
15.CHECK VALVE TIMING
a.
A301841C02
0.854,2.448 0.656,2.135 0.656,2.135 2.427,2.49 true 2.469,2.688 2.729,2.323 true 2.708,1.01 2.25,0.292 2.25,0.292 2.698,0.802 true 1.844,4.052 2.583,3.885 true 1.031,0.917 1.073,1.406 1.073,1.406 1.063,0.708 true 2.083,0.208 2.396,0.365 0.313,0.156 10 false *1 0.49,2.042 0.802,2.198 0.313,0.156 10 false *1 2.635,2.135 3.313,2.396 0.677,0.26 10 false 6°37' 0.25,0.188 0.698,0.427 0.448,0.24 10 false 13°47' 2.625,3.802 2.938,3.958 0.313,0.156 10 false *1 1.021,1.406 1.333,1.563 0.313,0.156 10 false *1
*1 Timing Mark


Remove the cylinder head cover.


b.

Turn the crankshaft to align the timing marks of the crankshaft.


c.

Align the groove of the crankshaft pulley with the "0" position.


d.

Confirm whether the timing marks of the camshaft pulley and cylinder head cover are facing each other.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

The timing marks of the camshaft pulley and the cylinder head cover face each other when the groove of the crankshaft pulley is in the "0" position.



Result:
Proceed to
OK
NG



OK

27.CHECK HARNESS AND CONNECTOR

NG

16.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage.

Click hereEngine / Hybrid System>2TR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leakage in air induction system.



Result:
Proceed to
OK
NG



OK

17.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

17.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

18.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)

NG

33.CHECK FUEL LINE
18.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 61 309

e.

Read Coolant Temp twice, when the engine is both cold and warmed up.

Standard:

With cold engine: Same as ambient air temperature.

With warm engine: Between 75°C and 100°C (167°F and 212°F).



Result:
Proceed to
OK
NG



OK

19.READ VALUE USING INTELLIGENT TESTER (MAF)

NG

19.READ VALUE USING INTELLIGENT TESTER (MAF)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.

Powertrain > Engine > Data List
Tester Display
MAF
Coolant Temp
50003 61 319,309

e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read MAF with the engine speed at 2500 rpm.

Standard:

Between 4 gm/s and 15 gm/s (shift lever: N; A/C: Off).



Result:
Proceed to
OK
NG



OK

20.CHECK VALVE TIMING

NG

27.CHECK HARNESS AND CONNECTOR
20.CHECK VALVE TIMING
a.
A301841C02
0.854,2.448 0.656,2.135 0.656,2.135 2.427,2.49 true 2.469,2.688 2.729,2.323 true 2.708,1.01 2.25,0.292 2.25,0.292 2.698,0.802 true 1.844,4.052 2.583,3.885 true 1.031,0.917 1.073,1.406 1.073,1.406 1.063,0.708 true 2.083,0.208 2.396,0.365 0.313,0.156 10 false *1 0.49,2.042 0.802,2.198 0.313,0.156 10 false *1 2.635,2.135 3.313,2.396 0.677,0.26 10 false 6°37' 0.25,0.188 0.698,0.427 0.448,0.24 10 false 13°47' 2.625,3.802 2.938,3.958 0.313,0.156 10 false *1 1.021,1.406 1.333,1.563 0.313,0.156 10 false *1
*1 Timing Mark


Remove the cylinder head cover.


b.

Turn the crankshaft to align the timing marks of the crankshaft.


c.

Align the groove of the crankshaft pulley with the "0" position.


d.

Confirm whether the timing marks of the camshaft pulley and cylinder head cover are facing each other.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

The timing marks of the camshaft pulley and the cylinder head cover face each other when the groove of the crankshaft pulley is in the "0" position.



Result:
Proceed to
OK
NG



OK

21.INSPECT SPARK PLUG

NG

21.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

22.CHECK FOR SPARKS AND IGNITION

NG

22.CHECK FOR SPARKS AND IGNITION
a.

Perform a spark test.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION

CAUTION:

Always disconnect all fuel injector connectors.


NOTICE:

Do not crank the engine for more than 2 seconds.


OK:

Sparks jump across electrode gap.



Result:
Proceed to
OK
NG



OK

23.CHECK CYLINDER COMPRESSION PRESSURE

NG

32.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
23.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>2TR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

24.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

24.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)
a.
A208644C09
0.458,0.615 0.781,0.844 0.323,0.229 0.458,0.917 0.781,1.146 0.323,0.229 0.458,1.208 0.781,1.438 0.323,0.229 0.458,1.5 0.781,1.729 0.323,0.229 0.094,0.094 0.469,0.344 0.375,0.25 10 false *a 0.49,0.656 0.865,0.906 0.375,0.25 10 false C65 0.531,0.958 0.906,1.208 0.375,0.25 10 false C2 0.5,1.25 0.875,1.5 0.375,0.25 10 false C66 0.542,1.542 0.917,1.792 0.375,0.25 10 false C4
*a Front view of wire harness connector
(to Fuel Injector Assembly)


Disconnect the fuel injector connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Cylinder Tester Connection Switch Condition Specified Condition
No. 1 C65-1 - Body ground Ignition switch ON 11 to 14 V
No. 2 C2-1 - Body ground Ignition switch ON 11 to 14 V
No. 3 C66-1 - Body ground Ignition switch ON 11 to 14 V
No. 4 C4-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

25.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)

NG

25.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)
a.

Disconnect the fuel injector connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Cylinder Tester Connection Condition Specified Condition
No. 1 C65-2 - Body ground Always 10 kΩ or higher
C65-2 - C76-6 (#10) Always Below 1 Ω
No. 2 C2-2 - Body ground Always 10 kΩ or higher
C2-2 - C76-5 (#20) Always Below 1 Ω
No. 3 C66-2 - Body ground Always 10 kΩ or higher
C66-2 - C76-2 (#30) Always Below 1 Ω
No. 4 C4-2 - Body ground Always 10 kΩ or higher
C4-2 - C76-1 (#40) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

26.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
a.

Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor].

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

27.CHECK HARNESS AND CONNECTOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

27.CHECK HARNESS AND CONNECTOR
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

Repair any problems.



Result:
Proceed to
NEXT



NEXT

28.CHECK WHETHER DTC OUTPUT RECURS
28.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the intelligent tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

j.

Input the DTC: P0300, P0301, P0302, P0303 or P0304.


k.

Check the DTC judgment result.

Result:
Result Proceed to
ABNORMAL
(P0300, P0301, P0302, P0303 or P0304 is output)
A
NORMAL
(No DTC is output)
B




A

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

B

END

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-3 (VG) - C76-28 (VG) Always Below 1 Ω
C36-2 (E2G) - C76-30 (E2G) Always Below 1 Ω
C36-3 (VG) or C76-28 (VG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

30.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL

HINT:

If the results of the inspections performed in steps 14 and 19 indicated no problem, proceed to the next step without replacing the mass air flow meter.



Result:
Proceed to
NEXT



NEXT

31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the intelligent tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

j.

Input the DTC: P0300, P0301, P0302, P0303 or P0304.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(No DTC is output)
A
ABNORMAL
(P0300, P0301, P0302, P0303 or P0304 is output)
B




A

END

B

32.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
a.

Change the installed spark plug to a spark plug that functions normally.


b.

Perform a spark test.

CAUTION:

Always disconnect all fuel injector connectors.


NOTICE:

Do not crank the engine for more than 2 seconds.


i.

Install the spark plug to the ignition coil and connect the ignition coil connector.


ii.

Disconnect the fuel injector connectors.


iii.

Ground the spark plug.


iv.

Check if sparks occur while the engine is being cranked.

OK:

Sparks jump across electrode gap.




Result:
Proceed to
OK
NG



OK

NG

34.CHANGE TO NORMAL IGNITION COIL ASSEMBLY AND CHECK SPARK OF MISFIRING CYLINDER
33.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE FUEL LINE

34.CHANGE TO NORMAL IGNITION COIL ASSEMBLY AND CHECK SPARK OF MISFIRING CYLINDER
a.

Change the ignition coil assembly to an ignition coil assembly that functions normally.


b.

Perform a spark test.

CAUTION:

Always disconnect all fuel injector connectors.


NOTICE:

Do not crank the engine for more than 2 seconds.


i.

Install the spark plug to the ignition coil and connect the ignition coil connector.


ii.

Disconnect the fuel injector connectors.


iii.

Ground the spark plug.


iv.

Check if sparks occur while the engine is being cranked.

OK:

Sparks jump across electrode gap.




Result:
Proceed to
OK
NG



OK

NG