A Direct Ignition System (DIS) is used on this vehicle to enhance ignition accuracy and suppress high voltage losses.
The DIS is an ignition system in which each cylinder is ignited by one ignition coil assembly. The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Based on the IGT signals, the ECM turns the power transistor inside the igniter on and off, turning the current to the primary coil on and off. When the current to the primary coil is cut off, a voltage is generated in the secondary coil and then applied to the spark plugs, causing them to spark inside the cylinders. At the same time, the igniter sends back the ignition confirmation (IGF) signal to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0351 | Ignition Coil "A" Primary / Secondary Circuit | No IGF signal is sent to the ECM while the engine is running (1 trip detection logic). | ·
Ignition system ·
Open or short in IGF1 or IGT 1 circuit between ignition coil and ECM ·
No. 1 ignition coil assembly ·
ECM |
Comes on | DTC stored |
| P0352 | Ignition Coil "B" Primary / Secondary Circuit | No IGF signal is sent to the ECM while the engine is running (1 trip detection logic). | ·
Ignition system ·
Open or short in IGF1 or IGT 2 circuit between ignition coil and ECM ·
No. 2 ignition coil assembly ·
ECM |
Comes on | DTC stored |
| P0353 | Ignition Coil "C" Primary / Secondary Circuit | No IGF signal is sent to the ECM while the engine is running (1 trip detection logic). | ·
Ignition system ·
Open or short in IGF1 or IGT 3 circuit between ignition coil and ECM ·
No. 3 ignition coil assembly ·
ECM |
Comes on | DTC stored |
| P0354 | Ignition Coil "D" Primary / Secondary Circuit | No IGF signal is sent to the ECM while the engine is running (1 trip detection logic). | ·
Ignition system ·
Open or short in IGF1 or IGT 4 circuit between ignition coil and ECM ·
No. 4 ignition coil assembly ·
ECM |
Comes on | DTC stored |
The following inspection procedure is for the No. 1 cylinder. If any of the other cylinders are malfunctioning, inspect their circuits by referring to the following procedure.
If DTC P0351 is output, check the ignition coil assembly No. 1 circuit.
If DTC P0352 is output, check the ignition coil assembly No. 2 circuit.
If DTC P0353 is output, check the ignition coil assembly No. 3 circuit.
If DTC P0354 is output, check the ignition coil assembly No. 4 circuit.
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0351, P0352, P0353 or P0354 is output | A |
| DTC P0351, P0352, P0353 and P0354 are output | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Shuffle the arrangement of the ignition coil assemblies (among the No. 1 to No. 4 cylinders).
Do not shuffle the connectors.
Perform a simulation test.
Check the DTCs output to the tester.
| Result | Proceed to |
|---|---|
| Same DTC output | A |
| Different ignition coil assembly DTC output | B |
A
B
| *a | Front view of wire harness connector
(to Ignition Coil Assembly) |
Disconnect the ignition coil assembly connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C70-1 (+B) - C70-4 (GND) | Ignition switch ON | 11 to 14 V |
| C71-1 (+B) - C71-4 (GND) | Ignition switch ON | 11 to 14 V |
| C72-1 (+B) - C72-4 (GND) | Ignition switch ON | 11 to 14 V |
| C73-1 (+B) - C73-4 (GND) | Ignition switch ON | 11 to 14 V |
Reconnect the ignition coil assembly connectors.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition coil assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C70-2 (IGF) - C98-10 (IGF1) | Always | Below 1 Ω |
| C71-2 (IGF) - C98-10 (IGF1) | Always | Below 1 Ω |
| C72-2 (IGF) - C98-10 (IGF1) | Always | Below 1 Ω |
| C73-2 (IGF) - C98-10 (IGF1) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C70-2 (IGF) or C98-10 (IGF1) - Body ground | Always | 10 kΩ or higher |
| C71-2 (IGF) or C98-10 (IGF1) - Body ground | Always | 10 kΩ or higher |
| C72-2 (IGF) or C98-10 (IGF1) - Body ground | Always | 10 kΩ or higher |
| C73-2 (IGF) or C98-10 (IGF1) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the ignition coil assembly connectors.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition coil assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C70-3 (IGT1) - C98-1 (IGT1) | Always | Below 1 Ω |
| C71-3 (IGT2) - C98-2 (IGT2) | Always | Below 1 Ω |
| C72-3 (IGT3) - C98-3 (IGT3) | Always | Below 1 Ω |
| C73-3 (IGT4) - C98-4 (IGT4) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C70-3 (IGT1) or C98-1 (IGT1) - Body ground | Always | 10 kΩ or higher |
| C71-3 (IGT2) or C98-2 (IGT2) - Body ground | Always | 10 kΩ or higher |
| C72-3 (IGT3) or C98-3 (IGT3) - Body ground | Always | 10 kΩ or higher |
| C73-3 (IGT4) or C98-4 (IGT4) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the ignition coil assembly connectors.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition coil assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C70-4 (GND) - Body ground | Always | Below 1 Ω |
| C71-4 (GND) - Body ground | Always | Below 1 Ω |
| C72-4 (GND) - Body ground | Always | Below 1 Ω |
| C73-4 (GND) - Body ground | Always | Below 1 Ω |
Reconnect the ignition coil assembly connectors.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition coil assembly connectors.
Disconnect the ignition switch assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C70-1 (+B) - G9-6 (IG2) | Always | Below 1 Ω |
| C71-1 (+B) - G9-6 (IG2) | Always | Below 1 Ω |
| C72-1 (+B) - G9-6 (IG2) | Always | Below 1 Ω |
| C73-1 (+B) - G9-6 (IG2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C70-1 (+B) or G9-6 (IG2) - Body ground | Always | 10 kΩ or higher |
| C71-1 (+B) or G9-6 (IG2) - Body ground | Always | 10 kΩ or higher |
| C72-1 (+B) or G9-6 (IG2) - Body ground | Always | 10 kΩ or higher |
| C73-1 (+B) or G9-6 (IG2) - Body ground | Always | 10 kΩ or higher |
Reconnect the ignition switch assembly connectors.
Reconnect the ignition coil assembly connectors.
| Proceed to |
|---|
| OK |
| NG |
OK
NG