Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter signal (STA signal) while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High When conditions (a), (b) and (c) are met, a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):

(a) The vehicle speed is more than 20 km/h (12.4 mph).

(b) The engine speed is more than 1000 rpm.

(c) The STA signal is on.


·

Short in starter signal circuit

·

Park/neutral position switch assembly (for Automatic Transmission)

·

Ignition switch assembly

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A242461
1.323,5.26 1.99,5.458 0.667,0.198 10 false Starter 1.781,1.042 2.208,1.24 0.427,0.198 10 false AM2 3.427,1.302 3.854,1.5 0.427,0.198 10 false ST 2.573,1.042 3,1.24 0.427,0.198 10 false ST2 3.417,4.49 3.75,4.688 0.333,0.198 10 false ST 6.5,5.938 6.938,6.135 0.438,0.198 10 false ECM 0.5,5.854 1.031,6.052 0.531,0.198 10 false Battery 4.677,1.813 5.042,2.01 0.365,0.198 10 false C57 1.531,1.667 1.875,1.833 0.344,0.167 10 false G9 1.479,4.156 1.646,4.344 0.167,0.188 10 false 1 2.958,1.042 3.125,1.229 0.167,0.188 10 false 7 1.583,1.042 1.75,1.229 0.167,0.188 10 false 5 4.354,1.688 4.521,1.875 0.167,0.188 10 false 4 4.125,2.427 4.292,2.615 0.167,0.188 10 false 5 3.073,3.625 3.24,3.813 0.167,0.188 10 false 3 3.823,3.646 3.99,3.833 0.167,0.188 10 false 5 3.063,4.073 3.229,4.26 0.167,0.188 10 false 2 3.823,4.063 3.99,4.25 0.167,0.188 10 false 1 5.844,1.74 6.073,1.927 0.229,0.188 10 false *1 4.542,1.344 4.771,1.531 0.229,0.188 10 false *2 4.396,6.01 6.24,6.219 1.844,0.208 10 false *1: for Manual Transmission 4.406,6.313 6.49,6.542 2.083,0.229 10 false *2: for Automatic Transmission 4.344,3.792 4.531,3.979 0.188,0.188 10 false *2 6.094,4.052 6.323,4.24 0.229,0.188 10 false 8 6.49,5.792 6.927,5.979 0.438,0.188 10 false G146 0.688,4.292 0.969,4.479 0.281,0.188 10 false 1 0.604,4.469 0.833,4.656 0.229,0.188 10 false D3 1.625,4.177 1.958,4.365 0.333,0.188 10 false C32 6.302,4.156 6.635,4.344 0.333,0.188 10 false STA 1.531,1.844 3.135,2.042 1.604,0.198 10 false Ignition Switch Assembly 4.667,1.99 5.771,2.552 1.104,0.563 10 false Park/Neutral Position Switch Assembly 6.042,1.115 6.323,1.302 0.281,0.188 10 false 24 6.281,1.229 6.927,1.417 0.646,0.188 10 false NSW*2 0.396,3.667 0.792,3.865 0.396,0.198 10 false AM2 3.104,5.792 4.729,6.052 1.625,0.26 10 false Theft Warning ECU 4.354,5.281 4.521,5.469 0.167,0.188 10 false 1 3,5.302 3.167,5.49 0.167,0.188 10 false 1 2.979,4.708 3.24,4.896 0.26,0.188 10 false 12 4.313,4.708 4.573,4.896 0.26,0.188 10 false 12 2.906,5.49 3.24,5.677 0.333,0.188 10 false G29 4.26,4.896 4.594,5.083 0.333,0.188 10 false G67 4.271,5.479 4.604,5.667 0.333,0.188 10 false G67 2.896,4.906 3.229,5.094 0.333,0.188 10 false G29

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

The following troubleshooting flowchart is based on the premise that the engine can be cranked normally.

If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

d.

Read the value displayed on the tester when the ignition switch is turned to ON and when the engine is started.

OK:
Condition Starter Signal
Ignition switch ON Close
Engine started Open


Result:
Result Proceed to
OK A
NG (for Manual Transmission) B
NG (for Automatic Transmission) C




A

B

2.INSPECT IGNITION SWITCH ASSEMBLY

C

5.INSPECT IGNITION SWITCH ASSEMBLY
2.INSPECT IGNITION SWITCH ASSEMBLY
a.
B119736
1,1.823 1.417,1.344 true 2.385,1.854 2,1.333 true 0.667,0.167 0.938,0.427 0.271,0.26 10 false *a 2.271,1.865 2.833,2.104 0.563,0.24 10 false AM2 0.854,1.844 1.125,2.104 0.271,0.26 10 false ST2
*a Component without harness connected
(Ignition Switch Assembly)


Disconnect the ignition switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (AM2) - 7 (ST2) LOCK 10 kΩ or higher
5 (AM2) - 7 (ST2) START Below 1 Ω



c.

Reconnect the ignition switch assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)

NG

REPLACE IGNITION SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-7 (ST2) or G146-8 (STA) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the ignition switch assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY [ST])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY [ST])
a.

Disconnect the ECM connector.


b.

Remove the starter relay (ST) from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Starter relay (ST) terminal 1 or G146-8 (STA) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reinstall the starter relay (ST).


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT IGNITION SWITCH ASSEMBLY
a.
B119736
1,1.823 1.417,1.344 true 2.385,1.854 2,1.333 true 0.667,0.167 0.938,0.427 0.271,0.26 10 false *a 2.271,1.865 2.833,2.104 0.563,0.24 10 false AM2 0.854,1.844 1.125,2.104 0.271,0.26 10 false ST2
*a Component without harness connected
(Ignition Switch Assembly)


Disconnect the ignition switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (AM2) - 7 (ST2) LOCK 10 kΩ or higher
5 (AM2) - 7 (ST2) START Below 1 Ω



c.

Reconnect the ignition switch assembly connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH)

NG

REPLACE IGNITION SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the park/neutral position switch connector.


b.

Disconnect the ignition switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-7 (ST2) or C57-4 - Body ground Always 10 kΩ or higher



d.

Reconnect the park/neutral position switch connector.


e.

Reconnect the ignition switch assembly connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STARTER RELAY [ST])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STARTER RELAY [ST])
a.

Disconnect the park/neutral position switch connector.


b.

Remove the starter relay (ST) from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Starter relay (ST) terminal 1 or C57-5 - Body ground Always 10 kΩ or higher



d.

Reconnect the park/neutral position switch connector.


e.

Reinstall the starter relay (ST).


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the park/neutral position switch connector.


b.

Disconnect the ECM connector.


c.

Remove the starter relay (ST) from the engine room relay block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C57-5 or G146-8 (STA) - Body ground Always 10 kΩ or higher



e.

Reconnect the park/neutral position switch connector.


f.

Reconnect the ECM connector.


g.

Reinstall the starter relay (ST).


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR