Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)  P2238  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)  P2239  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)  P2252  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)  P2253  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)  


DESCRIPTION

The air fuel ratio sensor generates a voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.

The air fuel ratio sensor is of the planar type and is integrated with a heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows through the heater to heat the sensor in order to facilitate accurate air-fuel ratio detection. In addition, the sensor and heater portions are the narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, thereby accelerating the sensor activation.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a Three-Way Catalytic Converter (TWC) is used. For the most efficient use of the Three-Way Catalytic Converter (TWC), the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: The value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A178930
1.615,2.938 1.01,2.438 false 1.76,2.917 1.969,2.635 false 2.865,2.104 3.281,0.729 false 3.01,2.094 3.198,1.542 false 3.146,2.156 3.729,2.01 false 2.948,2.677 3.396,2.521 3.396,2.521 2.792,2.813 false 3,2.896 3.427,3.208 false 1.01,2.438 0.917,2.438 false 1.969,2.635 2.042,2.635 false 3.427,3.208 3.51,3.208 false 3.396,2.521 3.5,2.521 false 3.063,0.729 3.281,0.729 false 3.198,1.542 3.333,1.542 false 0.208,3.125 1.156,3.365 0.948,0.24 10 false Exhaust Gas 0.375,2.344 1.031,2.531 0.656,0.188 10 false Element 2.083,2.552 2.531,2.802 0.448,0.25 10 false Cover 1.917,3.417 2.063,3.604 0.146,0.188 10 false A 1.25,3.417 1.396,3.604 0.146,0.188 10 false A 2.427,3.448 3.74,3.698 1.313,0.25 10 false A-A Cross Section 3.563,3.125 4.802,3.333 1.24,0.208 10 false Atmospheric Air 3.552,2.448 4.833,2.719 1.281,0.271 10 false Platinum Electrode 3.792,1.906 4.271,2.104 0.479,0.198 10 false Heater 3.375,1.458 4.125,1.688 0.75,0.229 10 false Alumina 1.927,0.594 3.135,0.969 1.208,0.375 10 false Solid Electrolyte (Zirconia Element) 5.615,3.49 6.583,3.688 0.969,0.198 10 false Air-fuel Ratio 4.604,0.75 6.135,1.302 1.531,0.552 10 false ECM Monitored Air Fuel Ratio Sensor Voltage 5.281,3.115 5.51,3.365 0.229,0.25 10 false 12 5.5,3.115 5.708,3.333 0.208,0.219 10 false 13 5.708,3.115 5.906,3.365 0.198,0.25 10 false 14 5.938,3.115 6.156,3.354 0.219,0.24 10 false 15 6.146,3.115 6.365,3.354 0.219,0.24 10 false 16 6.354,3.115 6.563,3.344 0.208,0.229 10 false 17 6.583,3.115 6.823,3.385 0.24,0.271 10 false 18 4.917,2.844 5.281,3.021 0.365,0.177 10 false 2.0 4.917,2.531 5.281,2.75 0.365,0.219 10 false 2.5 4.917,2.229 5.26,2.49 0.344,0.26 10 false 3.0 4.917,1.927 5.24,2.125 0.323,0.198 10 false 3.5 4.917,1.625 5.24,1.854 0.323,0.229 10 false 4.0

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) Open in the circuit between terminals AF+ and AF- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
·

Open in air fuel ratio sensor (Sensor 1) circuit

·

Air fuel ratio sensor (Sensor 1)

·

ECM


Comes on DTC stored
P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)
·

Case 1:


Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic):
(a) AF+ voltage is 0.5 V or less.
(b) (AF+) - (AF-) is 0.1 V or less.
·

Case 2:


Air fuel ratio sensor admittance is below 0.022 1/Ω (2 trip detection logic).
·

Open or short in air fuel ratio sensor (Sensor 1) circuit

·

Air fuel ratio sensor (Sensor 1)

·

ECM


Comes on DTC stored
P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) AF+ voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (Sensor 1) circuit

·

Air fuel ratio sensor (Sensor 1)

·

ECM


Comes on DTC stored
P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) AF- voltage is 0.5 V or less for 5.0 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (Sensor 1) circuit

·

Air fuel ratio sensor (Sensor 1)

·

ECM


Comes on DTC stored
P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) AF- voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (Sensor 1) circuit

·

Air fuel ratio sensor (Sensor 1)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs are output when there is an open or short in the air fuel ratio sensor circuit, or if the air fuel ratio sensor output drops.

To detect these problems, the voltage of the air fuel ratio sensor is monitored when turning the ignition switch to ON, and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the air fuel ratio sensor is between 0.6 V and 4.5 V, it is considered normal. If the voltage is outside of the specified range, or the admittance is below the standard value, the ECM will determine that there is a malfunction in the air fuel ratio sensor. If the same malfunction is detected in the next driving cycle, the MIL is illuminated and a DTC is stored.

The air fuel ratio sensor varies its output voltage in proportion to the air-fuel ratio. If the air fuel ratio sensor impedance (alternating current resistance) or output voltage deviates greatly from the standard range, the ECM determines that there is an open or short in the air fuel ratio sensor circuit.

MONITOR STRATEGY

Required Sensors/Components Air fuel ratio sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Start the engine and wait for 5 minutes or more.


WIRING DIAGRAM

A247781
5.74,0.427 6.26,0.677 0.521,0.25 10 false HA1A 4.188,0.438 4.677,0.646 0.49,0.208 10 false HA1A 5.5,0.375 5.615,0.531 0.115,0.156 10 false 1 5.406,0.563 5.792,0.76 0.385,0.198 10 false C75 5.406,1.344 5.781,1.521 0.375,0.177 10 false C75 5.406,2.021 5.813,2.26 0.406,0.24 10 false C75 5.74,1.208 6.26,1.458 0.521,0.25 10 false A1A+ 4.219,1.167 4.729,1.375 0.51,0.208 10 false A1A+ 5.469,1.156 5.74,1.375 0.271,0.219 10 false 21 5.458,1.844 5.75,2.021 0.292,0.177 10 false 31 5.74,1.896 6.229,2.156 0.49,0.26 10 false A1A- 3.781,1.167 4.156,1.396 0.375,0.229 10 false A1A- 5.74,3.042 6.26,3.323 0.521,0.281 10 false MREL 5.5,2.844 5.615,3 0.115,0.156 10 false 8 5.406,3.031 5.792,3.24 0.385,0.208 10 false G89 4.958,2.417 5.615,2.646 0.656,0.229 10 false Shielded 3.458,1.708 4.865,1.896 1.406,0.188 10 false Air Fuel Ratio Sensor 3.448,1.542 3.75,1.698 0.302,0.156 10 false C85 3.792,0.438 4.083,0.708 0.292,0.271 10 false +B 6.198,4.813 6.656,5.052 0.458,0.24 10 false ECM 4.635,0.438 4.76,0.604 0.125,0.167 10 false 1 3.625,0.438 3.75,0.604 0.125,0.167 10 false 2 4.635,1.219 4.76,1.385 0.125,0.167 10 false 3 3.625,1.219 3.75,1.385 0.125,0.167 10 false 4 1.542,0.448 1.656,0.604 0.115,0.156 10 false 5 1.542,0.74 1.656,0.896 0.115,0.156 10 false 1 2.292,0.448 2.406,0.604 0.115,0.156 10 false 3 2.292,0.74 2.406,0.896 0.115,0.156 10 false 2 0.885,2.115 1.094,2.271 0.208,0.156 10 false 1J 2.604,3.031 2.813,3.188 0.208,0.156 10 false 1J 2.604,3.615 2.875,3.833 0.271,0.219 10 false 1J 1.146,2.125 1.26,2.281 0.115,0.156 10 false 5 2.646,2.844 2.76,3 0.115,0.156 10 false 2 2.646,3.438 2.76,3.594 0.115,0.156 10 false 3 0.875,3.792 1.177,3.979 0.302,0.188 10 false 1H 1.146,3.781 1.26,3.938 0.115,0.156 10 false 1 0.5,0.698 0.823,0.958 0.323,0.26 10 false A/F 1.865,1.156 2.229,1.438 0.365,0.281 10 false A/F 1.115,2.875 1.448,3.115 0.333,0.24 10 false EFI 1.781,3.313 2.156,3.479 0.375,0.167 10 false MAIN 1.063,4.688 1.844,4.958 0.781,0.271 10 false BATT P/I 1.208,5.927 1.865,6.188 0.656,0.26 10 false Battery 1.313,3.99 2.875,4.26 1.563,0.271 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C85-1 (HA1A) - C75-1 (HA1A) Always Below 1 Ω
C85-3 (A1A+) - C75-21 (A1A+) Always Below 1 Ω
C85-4 (A1A-) - C75-31 (A1A-) Always Below 1 Ω
C85-1 (HA1A) or C75-1 (HA1A) - Body ground Always 10 kΩ or higher
C85-3 (A1A+) or C75-21 (A1A+) - Body ground Always 10 kΩ or higher
C85-4 (A1A-) or C75-31 (A1A-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE AIR FUEL RATIO SENSOR

Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Start the engine.


f.

Allow the engine to idle for 5 minutes or more.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the pending DTCs.

Result:
Result Proceed to
No DTC is output A
P2237, P2238, P2239, P2252 or P2253 is output B




A

END

B