Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/o Secondary Air Injection System) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052091 SFI SYSTEM(w/o Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If signals which indicate the brake pedal is being depressed and released are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the intelligent tester, the Data List items Stop Light Switch and ST1 are both ON when the brake pedal is depressed because the characteristics of ST1 indication are the opposite of the characteristics of Stop Light Switch indication.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a), (b) and (c) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) STP signal is OFF when the ST1- signal is OFF.
·

Short in stop light switch signal circuit

·

STOP fuse

·

Stop light switch assembly

·

ECM


- DTC stored

WIRING DIAGRAM

A247775
5.49,0.563 5.792,0.802 0.302,0.24 10 false 16 5.792,0.635 6.24,0.896 0.448,0.26 10 false ST1- 5.542,1.625 5.656,1.792 0.115,0.167 10 false 4 5.792,1.729 6.25,1.958 0.458,0.229 10 false STP 5.448,1.844 5.844,2.052 0.396,0.208 10 false G88 5.438,0.771 5.781,0.99 0.344,0.219 10 false G89 6.198,2.885 6.677,3.104 0.479,0.219 10 false ECM 4.115,0.635 4.24,0.792 0.125,0.156 10 false 3 4.927,0.635 5.052,0.792 0.125,0.156 10 false 4 4.927,1.719 5.052,1.875 0.125,0.156 10 false 1 4.115,1.719 4.24,1.875 0.125,0.156 10 false 2 4.021,2.208 4.396,2.417 0.375,0.208 10 false A24 4.021,2.354 5.26,2.635 1.24,0.281 10 false Stop Light Switch 3.063,2.01 3.573,2.281 0.51,0.271 10 false STOP 1.333,1.125 1.75,1.396 0.417,0.271 10 false G9 1.333,1.271 2.365,1.51 1.031,0.24 10 false Ignition Switch 2.25,0.625 2.375,0.781 0.125,0.156 10 false 6 1.24,0.625 1.365,0.781 0.125,0.156 10 false 5 1.948,0.885 2.26,1.073 0.313,0.188 10 false IG2 3.146,0.906 3.542,1.146 0.396,0.24 10 false IGN 1.396,0.885 1.802,1.104 0.406,0.219 10 false AM2 0.635,1.365 1.052,1.583 0.417,0.219 10 false AM2 1.646,2.031 2.052,2.292 0.406,0.26 10 false ALT 0.792,2.885 1.427,3.135 0.635,0.25 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following procedure.


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the intelligent tester on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch and ST1.

5.

Check the Data List indication when the brake pedal is depressed and released.




Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / All Data / Stop Light Switch.

Powertrain > Engine > Data List
Tester Display
Stop Light Switch
50003 61 188

e.

Read the value displayed on the intelligent tester.

Standard:
Condition Specified Condition
Brake pedal depressed STP signal ON
Brake pedal released STP signal OFF



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT STOP LIGHT SWITCH ASSEMBLY (B+ VOLTAGE)
2.INSPECT STOP LIGHT SWITCH ASSEMBLY (B+ VOLTAGE)
a.
A148738
0.688,1.813 1.031,2.052 0.344,0.24 0.094,0.052 0.375,0.333 0.281,0.281 10 false *a 0.74,1.844 1.073,2.073 0.333,0.229 10 false A24
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-2 - Body ground Always 11 to 14 V
A24-3 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH - BATTERY, IGNITION SWITCH)

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT ECM (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.INSPECT ECM (STP AND ST1- VOLTAGE)
a.
A301839
1.49,4.01 1.948,3.698 true 1.813,4.406 2.375,3.771 true 0.948,0.469 1.26,0.625 0.313,0.156 10 false *a 2.49,0.479 2.802,0.635 0.313,0.156 10 false *b 0.104,2.24 0.448,2.427 0.344,0.188 10 false *c 1,3.958 1.656,4.188 0.656,0.229 10 false 4 (STP) 1.75,4.427 2.469,4.646 0.719,0.219 10 false 16 (ST1-)
*a Depressed
*b Released
*c Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G89-16 (ST1-) - Body ground Brake pedal released 11 to 14 V
Brake pedal depressed 0 to 3 V
G88-4 (STP) - Body ground Brake pedal released 0 to 3 V
Brake pedal depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STOP LIGHT SWITCH)