Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/ EGR Cooler) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052102 ECD SYSTEM(w/ EGR Cooler) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  P1251  Turbocharger / Supercharger Overboost Condition (Too High)  


DESCRIPTION

HINT:

Refer to DTC P0046 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>P0046).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1251 Turbocharger / Supercharger Overboost Condition (Too High) Boost pressure is higher than the threshold* for 0.5 seconds. (1 trip detection logic).
·

Turbocharger sub-assembly

·

VN turbo link stuck malfunction

·

Extremely low battery voltage (P0560 stored simultaneously)

·

Intake system

·

Exhaust system

·

Electric EGR control valve assembly

·

EGR cooler

·

Injector assembly

·

Diesel throttle body assembly

·

ECM


Comes on DTC stored

HINT:

*: This value changes based on engine speed, atmospheric pressure and the engine coolant temperature (the value is generally between 177 and 250 kPa).


Related Data List
DTC No. Data List
P1251
·

MAP

·

Target Booster Pressure

·

MAF

·

Target EGR Position

·

Actual EGR Valve Pos.

·

VN Turbo Command

·

Atmosphere Pressure



HINT:

If DTC P1251 is stored due to the VN turbo vane being stuck closed, the following symptoms may appear:

·

Vehicle surge when driving with full load

·

Sudden lack of power due to power being limited



CONFIRMATION DRIVING PATTERN

P1251
DTC Detection Drive Pattern Vehicle being driven

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

HINT:
·

Record the stored DTC and Freeze Frame Data.

·

Be sure to carefully examine "MAP" and "Target Booster Pressure" in the freeze frame data.



Result:
Result Proceed to
P1251 is output A
P1251 and other DTCs are output B


HINT:

DC motor-related DTCs: P0046 (See pageEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>P0046), P0047 and P0048 (See pageEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>P0047).

Nozzle vane position sensor-related DTCs: P2563, P2564, P2565, P2588 and P2589 (See pageEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>P2563).




A

2.CHECK AIR INTAKE SYSTEM

B

2.CHECK AIR INTAKE SYSTEM
a.

Check if the hoses between the air cleaner and turbocharger, and turbocharger and intake manifold are damaged or disconnected.

Result:
Result Proceed to
Hoses or pipes are damaged or disconnected A
No hoses or pipes are damaged or disconnected B


HINT:
·

Be sure to check if the hoses and pipes between the air cleaner and compressor are disconnected as disconnection of a hose or pipe can cause overboost. Also, check the high pressure hoses for disconnection due to overboost.

·

Check for disconnection of the exhaust pipes.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

Check for any modifications in the intake system made by the user.





A

3.REPAIR OR REPLACE AIR INTAKE SYSTEM

B

4.CHECK TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)
3.REPAIR OR REPLACE AIR INTAKE SYSTEM
a.

Repair or replace the malfunctioning part in the air intake system.


Result:
Proceed to
NEXT



NEXT

4.CHECK TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)
4.CHECK TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)
a.

Check the turbocharger sub-assembly.

Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>INTAKE SYSTEM(w/o Glow Plug Controller)>ON-VEHICLE INSPECTION

HINT:

Check the movement of the actuator rod when the ignition switch is turned from ON to off.



Result:
Proceed to
OK
NG



OK

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE EGR VALVE CLOSE)

NG

9.CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - TURBOCHARGER SUB-ASSEMBLY)
5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE EGR VALVE CLOSE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


c.

Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

Powertrain > Engine > Data List
Tester Display
MAF
50003 61 319

f.

Read the MAF value displayed on the tester while the engine is idling.


g.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR Valve Close.

Powertrain > Engine > Active Test
Tester Display
Activate the EGR Valve Close
50004 61 183

h.

Read the MAF value when the EGR valve is closed using the Active Test function.

HINT:
·

If idling continues for 15 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or to restart the engine.

·

Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.

·

When "Coolant Temp" is 75°C (167°F) or higher during idling, the exhaust gas flows through the EGR cooler. If MAF does not change when the EGR is cut even though the EGR valve is operating normally, the EGR cooler may be clogged.

·

When idling while warming up the engine, the actuator operates and the EGR cooler is bypassed. However, if the connector of the VSV for the EGR cooler is disconnected, the EGR cooler is not bypassed and it is possible to check how clogged the EGR cooler is.



Result:
Active Test Result Proceed to
Activate the EGR Valve Close:
Off (Open) to On (Closed)
MAF value does not change A
MAF value changes B


NOTICE:

As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.


HINT:

The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric vacuum regulating valve assembly, electric EGR control valve assembly or mass air flow meter.


Reference:
EGR Valve Condition (Opening) Measuring Condition MAF (Reference)
Open (55%)
·

Atmosphere pressure: 101 kPa

·

Intake air temperature: 30°C (86°F)

·

Engine coolant temperature: 88°C (190°F)


3.0 to 9.0 gm/s
Closed (0%) 15 to 22 gm/s




A

6.READ VALUE USING INTELLIGENT TESTER (TARGET EGR POSITION AND ACTUAL EGR VALVE POS.)

B

10.READ VALUE USING INTELLIGENT TESTER (INJECTION VOLUME)
6.READ VALUE USING INTELLIGENT TESTER (TARGET EGR POSITION AND ACTUAL EGR VALVE POS.)
a.

Check the change in the values of "Target EGR Position" and "Actual EGR Valve Pos." in the Data List from the time when the "Activate The EGR valve Close" Active Test was performed in the previous step.

Result:
Result Proceed to
Even though "Target EGR Position" indicated that the system was commanding the valve to open, "Actual EGR Valve Pos." remained near 0% and did not change A
Other than above ("Actual EGR Valve Pos." changed according to the EGR valve open/close commands of the Active Test) B




A

7.CHECK ELECTRIC EGR CONTROL VALVE ASSEMBLY (CHECK VACUUM)

B

15.REPLACE EGR COOLER
7.CHECK ELECTRIC EGR CONTROL VALVE ASSEMBLY (CHECK VACUUM)
a.
A245207
2.292,0.084 3.198,0.366 0.906,0.281 10 Vacuum Hose 1.527,0.425 2.245,0.168 false

Disconnect the vacuum hose from the electric EGR control valve assembly.


b.

Start the engine.


c.

Check if there is suction from the vacuum hose during idling.

HINT:

If idling continues for 15 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or to restart the engine.


OK:

Suction exists.



Result:
Proceed to
OK
NG



OK

8.REMOVE DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)

NG

16.REPAIR OR REPLACE VACUUM HOSE
8.REMOVE DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
a.

b.

Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.

NOTICE:
·

When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.

·

Do not forcibly open the valve, as it may be damaged or deformed.

·

When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.



HINT:
·

If the EGR valve is stuck closed, the intake air amount increases and engine vibration may worsen.

·

If the EGR valve does not operate due to clogging or disconnection of the vacuum hose, repair the hose.

·

If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power.




c.

Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - TURBOCHARGER SUB-ASSEMBLY)
a.

Disconnect the DC motor connector.


b.

Disconnect the nozzle vane position sensor connector.


c.

Disconnect the turbo motor driver connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-2 (M+) - C39-12 (M+) Always Below 1 Ω
C41-1 (M-) - C39-5 (M-) Always Below 1 Ω
C40-1 (VTA1) - C39-9 (VTA1) Always Below 1 Ω
C40-2 (VNE2) - C39-8 (VNE2) Always Below 1 Ω
C40-3 (VNVC) - C39-1 (VNVC) Always Below 1 Ω
C40-4 (VTA2) - C39-10 (VTA2) Always Below 1 Ω
C40-5 (E2S) - C39-11 (E2S) Always Below 1 Ω
C40-6 (VCS) - C39-6 (VCS) Always Below 1 Ω
C41-2 (M+) or C39-12 (M+) - Body ground Always 10 kΩ or higher
C41-1 (M-) or C39-5 (M-) - Body ground Always 10 kΩ or higher
C40-1 (VTA1) or C39-9 (VTA1) - Body ground Always 10 kΩ or higher
C40-2 (VNE2) or C39-8 (VNE2) - Body ground Always 10 kΩ or higher
C40-3 (VNVC) or C39-1 (VNVC) - Body ground Always 10 kΩ or higher
C40-4 (VTA2) or C39-10 (VTA2) - Body ground Always 10 kΩ or higher
C40-5 (E2S) or C39-11 (E2S) - Body ground Always 10 kΩ or higher
C40-6 (VCS) or C39-6 (VCS) - Body ground Always 10 kΩ or higher



e.

Reconnect the DC motor connector.


f.

Reconnect the nozzle vane position sensor connector.


g.

Reconnect the turbo motor driver connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.READ VALUE USING INTELLIGENT TESTER (INJECTION VOLUME)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 70°C (158°F) or higher.


c.

Allow the engine to idle for 1 minute or more.

HINT:

The A/C switch and all accessory switches should be off with a fully warm engine.



d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Volume.

Powertrain > Engine > Data List
Tester Display
Injection Volume
50003 61 376

f.

Read the values during engine idling.

Result:
Result Proceed to
Injection Volume is less than 5 mm3/st A
Except above B


HINT:
·

If the injector assembly is malfunctioning, the compensatory injection volume remains at 5.0 mm3/st.

·

If there is a disconnection, the feedback value will increase and +5.0 mm3/st will be indicated, because it will become impossible for the injector to inject.





A

11.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

B

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

Result:
Proceed to
NEXT



NEXT

12.BLEED AIR FROM FUEL SYSTEM
12.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

13.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
13.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation code.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Injector Compensation
50005 61 239

b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Pilot Quantity Learning
50005 61 235

Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off.


d.

Start the engine and warm it up.


e.

Confirm the value of Engine Speed from the Freeze Frame Data recorded previously, and then drive the vehicle according to the Engine Speed value.

HINT:

Take a snapshot of MAP and Target Boost Pressure in the Data List with the intelligent tester while driving the vehicle.



f.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
P1251 is not output and the amount by which MAP exceeds Target Boost Pressure is 20 kPa or less A
Except above B*


HINT:

*: Return to "Check Air Intake System" and inspect areas that have not been inspected yet.




A

END

B*

2.CHECK AIR INTAKE SYSTEM
15.REPLACE EGR COOLER
a.

Replace the EGR cooler.


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.REPAIR OR REPLACE VACUUM HOSE
a.

Repair or replace of the EGR valve system vacuum hose.


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED