The turbocharger system is comprised of the Variable Nozzle (VN) type turbocharger, the turbo motor driver and ECM.
The turbocharger has a nozzle vane which opens and closes to control the volume of the exhaust gas flowing into the turbine. This, in turn, controls the boost pressure, when the nozzle vane moves towards the closing direction, the pressure increases. When the vane moves towards the opening direction, the pressure decreases.
The turbocharger actuator, which consists of the DC motor and the nozzle vane position sensor, is built on the turbocharger sub-assembly, and activates the nozzle vane. The nozzle vane position sensor detects the opening angle of the nozzle vane. The turbo motor driver receives an opening angle request from the ECM and a nozzle vane position signal from the nozzle vane position sensor. Based on these signals, the turbo motor driver operates the DC motor and adjusts the nozzle vane opening angle. The turbo motor driver sends the status as a turbo driver status signal to the ECM
The ECM sends a target nozzle vane position signal to the turbo motor driver to obtain the nozzle vane position for the optimal boost pressure in accordance with the driving conditions.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1264 | VN Turbo Controller Malfunction | When communication error occurs between turbo motor and ECM
(1 trip detection logic) |
·
Turbo motor driver ·
Open or short in turbo motor driver circuit ·
Turbo motor driver ground problem ·
ECM |
Comes on | DTC stored |
| DTC Detection Drive Pattern | Ignition switch to ON for 5 seconds |
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>INITIALIZATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Excessive electrical noise, such as from wireless radios or electrical modifications, may cause a DTC output.
| *a | Front view of wire harness connector
(to Turbo Motor Driver) |
Disconnect the turbo motor driver connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C39-3 (+B) - C39-4 (GND) | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C39-4 (GND) - Body ground | Always | Below 1 Ω |
Reconnect the turbo motor driver connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the turbo motor driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C22-10 (VNTO) - C39-7 (VNTO) | Always | Below 1 Ω |
| C22-17 (VNTI) - C39-2 (VNTI) | Always | Below 1 Ω |
| C22-10 (VNTO) or C39-7 (VNTO) - Body ground | Always | 10 kΩ or higher |
| C22-17 (VNTI) or C39-2 (VNTI) - Body ground | Always | 10 kΩ or higher |
Reconnect the turbo motor driver connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(ECM) |
While idling the engine, check the waveform of the ECM connectors using an oscilloscope.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C22-10 (VNTO) - C23-7 (E1) | Idling | Correct waveform is as shown |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(ECM) |
While idling the engine, check the waveform of the ECM connectors using an oscilloscope.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C22-17 (VNTI) - C23-7 (E1) | Idling | Correct waveform is as shown |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace turbo motor driver.
Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>TURBO MOTOR DRIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR
Turn the ignition switch off.
Remove the EFI fuse from the engine room relay block and junction block assembly for more than 1 minute.
Turn the ignition switch to ON and wait for 10 seconds or more.
Start the engine.
Drive the vehicle with a city driving pattern at least 10 minutes.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT