Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/ EGR Cooler) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052102 ECD SYSTEM(w/ EGR Cooler) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  P1271  Fuel Regulator Circuit Malfunction (EDU Drive)  P1272  Fuel Pressure Regulator Malfunction  


DESCRIPTION

The ECM controls the internal fuel pressure of the common rail by opening and closing the pressure discharge valve. When sudden deceleration occurs, the internal fuel pressure will temporarily become higher than usual and combustion noise may result. Therefore the ECM will open the valve temporarily to discharge the excess pressure inside the common rail. Also, the pressure discharge valve opens when the ignition switch is turned off to allow prompt discharge of the common rail internal pressure and so that the engine stops smoothly.

HINT:
·

For more information on the pressure discharge valve and common rail system, refer to System Description (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>SYSTEM DESCRIPTION).

·

For more information on the injector driver, refer to System Description (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>SYSTEM DESCRIPTION).

·

If P1271 and/or P1272 is present, refer to the DTC chart for the fuel system (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>SYSTEM DESCRIPTION).



A208468
3.719,2.781 3.49,2.781 false 3.667,3 3.479,3.135 3.479,3.135 3.396,3.135 false 3.896,2.427 4.083,2.229 4.083,2.229 4.188,2.229 false 0.052,0.031 4.219,0.313 4.167,0.281 10 false Pressure Discharge Valve Operation Due to Sudden Deceleration: 0.927,0.375 2.042,0.771 1.115,0.396 10 false Accelerator Pedal Opening Angle 0.385,1.385 2.042,1.688 1.656,0.302 10 false Pressure Discharge Valve 1.125,2.292 2.094,2.573 0.969,0.281 10 false Fuel Pressure 2.604,0.542 2.99,0.76 0.385,0.219 10 false Open 4.188,1.406 4.646,1.656 0.458,0.25 10 false Open 2.594,1.188 3.146,1.521 0.552,0.333 10 false Closed 4.135,0.75 4.708,1.01 0.573,0.26 10 false Closed 4.25,2.135 6.229,2.375 1.979,0.24 10 false w/o Pressure Discharge Valve 1.688,2.688 3.552,2.938 1.865,0.25 10 false w/ Pressure Discharge Valve 2.073,3.042 3.5,3.26 1.427,0.219 10 false Target Fuel Pressure 3.979,3.281 5.125,3.521 1.146,0.24 10 false Time Reduction 3.427,3.552 3.792,3.76 0.365,0.208 10 false Time

A081505
3.979,1.469 4.135,0.917 4.135,0.917 4.24,0.917 false 3.406,0.625 3.49,0.625 3.49,0.625 3.656,1.75 false 0.094,0.063 3.365,0.365 3.271,0.302 10 false Cross Section Diagram of Pressure Discharge Valve: 0.146,1.563 1.365,2.146 1.219,0.583 10 false From Common Rail Assembly (High Pressure) 5.604,0.125 6.875,0.833 1.271,0.708 10 false Return to Fuel Tank Sub-assembly (Low Pressure) 3.052,0.542 3.479,0.76 0.427,0.219 10 false Valve 4.271,0.844 4.958,1.104 0.688,0.26 10 false Solenoid

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1271 Fuel Regulator Circuit Malfunction (EDU Drive) Either condition is met (1 trip detection logic):
·

Open or short in pressure discharge valve circuit.

·

There is no valve opening confirmation (INJF) signal from the injector driver to the ECM for a specific number of times consecutively despite the ECM sending valve opening command (PRD) signals after the engine is started.


·

Open or short in pressure discharge valve circuit

·

Pressure discharge valve

·

Injector driver


Comes on DTC stored
P1272 Fuel Pressure Regulator Malfunction Pressure discharge valve does not open.
Actual pressure decreasing rate deviates from the simulated pressure decreasing rate after the ignition switch is turned off (2 trip detection logic).
·

Open or short in pressure discharge valve circuit (P1271 is stored simultaneously)

·

Pressure discharge valve

·

Injector driver

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P1271
·

Fuel Press

·

Target Common Rail Pressure

·

Pressure discharge valve


P1272

HINT:
·

After confirming DTC P1271 and/or P1272, check the fuel pressure inside the common rail by entering the following menus:

Powertrain / Engine and ECT / Data List / Fuel Press.

·

P1271:

After clearing the DTC, drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Check that P1271 is not output.

·

P1272:

After clearing the DTC, start and stop the engine twice (wait 30 seconds or more after turning the ignition switch off before starting the engine the second time), and then confirm that P1272 is not stored.


Reference
Engine Speed Fuel Pressure (kPa)
Idling Fuel press is within 5000 kPa of Target Common Rail Pressure
2500 rpm (No engine load)


CONFIRMATION DRIVING PATTERN

P1271
DTC Detection Drive Pattern Ignition switch ON to off
and
Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal

P1272
DTC Detection Drive Pattern Ignition switch ON to off

MONITOR DESCRIPTION

P1271 (Open or short in pressure discharge valve circuit):

This DTC will be stored if there is no valve opening confirmation (INJF) signal sent from the injector driver to the ECM despite the ECM commanding the injector driver to open the pressure discharge valve. This DTC refers to an open or short circuit malfunction of the pressure discharge valve circuit, not a malfunction in which a valve is stuck open or closed.

The injector driver monitors the current supplied to the pressure discharge valve to verify that the current flows into the valve. If the current exceeds the specified level, the injector driver interprets this as the INJF signal being low. If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

A208469
3.854,2.771 3.969,2.51 3.969,2.51 4.125,2.51 false 3.854,3.115 3.781,3.396 3.781,3.396 3.646,3.396 false 0.115,0.052 1.438,0.208 1.323,0.156 10 false P1271 Malfunction: 0.188,1.906 1.781,2.427 1.594,0.521 10 false Pressure Discharge Valve Command Signal 1.979,1.969 2.354,2.156 0.375,0.188 10 false PRD 2.344,0.198 2.719,0.385 0.375,0.188 10 false ECM 5.5,0.198 6.469,0.385 0.969,0.188 10 false Injector Driver 2.833,1.365 3.104,1.552 0.271,0.188 10 false On 3.292,1.76 3.542,1.948 0.25,0.188 10 false Off 4.177,2.417 4.896,2.698 0.719,0.281 10 false Abnormal 3.167,3.302 3.656,3.563 0.49,0.26 10 false Normal 0.177,2.625 1.76,3.094 1.583,0.469 10 false Pressure Discharge Valve Confirmation Signal 2.01,2.708 2.406,2.896 0.396,0.188 10 false INJF 3.385,1.198 5.25,1.458 1.865,0.26 10 false Confirmation Signal (INJF) 3.365,0.479 5.115,0.781 1.75,0.302 10 false Command Signal (PRD)


P1272 (Pressure discharge valve stuck closed):

The pressure discharge valve will open and discharge the internal fuel pressure from the common rail to the fuel tank when the ignition switch is turned off. In this event, the ECM compares the actual drop rate of the internal fuel pressure and the target drop rate. If the ECM judges that the actual drop rate is smaller than the target, the ECM then determines that the valve is stuck closed and stores this DTC. This DTC will be stored if the internal fuel pressure does not drop to the target after the ignition switch has been turned off.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


MONITOR STRATEGY

P1271
Required sensors Injector driver
Frequency of operation Continuous
Duration 3 seconds
MIL operation 1 driving cycle

P1272
Required sensors Fuel pressure sensor
Frequency of operation Once per driving cycle
Duration 1 second
MIL operation 2 driving cycles

TYPICAL ENABLING CONDITIONS

P1271
Specification
The vehicle is driven at 50 km/h (31 mph) in 3rd gear, and then decelerated by complete release of the accelerator pedal 3 times.

P1272
Item Specification
Minimum Maximum
Fuel pressure 27000 kPa (275 kgf/cm2, 3915 psi) -
Fuel temperature 0°C (32°F) -
Battery voltage 11 V -
The monitor will not run if the fuel pressure sensor, pressure discharge valve circuit or fuel temperature sensor is malfunctioning.

TYPICAL MALFUNCTION THRESHOLDS

P1271
Specification
There are no confirmation signals from the injector driver for a specific number of times consecutively, despite the ECM sending command signals regularly during deceleration.

P1272
Specification
The internal pressure stays beyond the specified level after the ignition switch is turned off.

WIRING DIAGRAM

A255255
0.969,2.719 1.344,2.906 0.375,0.188 10 false RLF- 1.385,2.719 1.74,2.885 0.354,0.167 10 false C44 1.469,2.521 1.615,2.677 0.146,0.156 10 false 1 1.031,0.885 1.365,1.073 0.333,0.188 10 false INJF 1.375,0.885 1.74,1.052 0.365,0.167 10 false C45 1.469,0.667 1.615,0.823 0.146,0.156 10 false 5 5.844,0.875 6.177,1.063 0.333,0.188 10 false INJF 5.604,0.771 5.781,0.927 0.177,0.156 10 false 25 5.833,1.354 6.167,1.542 0.333,0.188 10 false PRD 6.104,3.073 6.417,3.24 0.313,0.167 10 false C22 5.604,1.24 5.781,1.396 0.177,0.156 10 false 32 0.948,1.781 1.396,1.969 0.448,0.188 10 false RLF+ 1.375,1.781 1.729,1.948 0.354,0.167 10 false C43 1.469,1.573 1.615,1.729 0.146,0.156 10 false 4 0.969,1.344 1.302,1.531 0.333,0.188 10 false PRD 1.375,1.354 1.74,1.521 0.365,0.167 10 false C45 1.469,1.135 1.615,1.292 0.146,0.156 10 false 2 6.094,3.24 6.458,3.417 0.365,0.177 10 false ECM 0.74,3.083 1.104,3.26 0.365,0.177 10 false EDU 1.896,3.042 2.583,3.219 0.688,0.177 10 false (Shielded) 3.698,2.063 4.021,2.208 0.323,0.146 10 false C99 3.688,2.198 5.302,2.396 1.615,0.198 10 false Pressure Discharge Valve 4.052,1.875 4.177,2.094 0.125,0.219 10 false 2 4.781,1.875 4.906,2.01 0.125,0.135 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>INITIALIZATION).


HINT:
·

After completing repairs, confirm that P1271 and/or P1272 does not recur.

·

If P0200 and P1271 are present simultaneously, there is an open in the INJF wire harness between the injector driver and ECM, or there is an open in the wire harness for both an injector assembly and the pressure discharge valve.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK IF DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

g.

Read the pending DTCs.

Result:
Result Proceed to
P1272 A
P1271 B
P1271 and P1272 B
Other DTCs output C




A

2.CHECK COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE OPERATION)

B

6.INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE RESISTANCE)

C

2.CHECK COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE OPERATION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain /Engine / Utility / Pressure Discharge Valve Check.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DATA LIST / ACTIVE TEST

Powertrain > Engine > Utility
Tester Display
Pressure Discharge Valve Check
50005 61 2109

d.

Select "Close to Open Check".


e.

Read the value of "Open and Engine OFF".

OK:

0.5 MPa or less


HINT:
·

When the system is normal, the value of "Open and Engine OFF" should be at or close to 0 MPa.

·

When the fuel pressure value of "Open and Engine OFF" does not become equal to or less than 0.5 MPa, the pressure discharge valve may be stuck closed.

·

When the fuel pressure values of "Close and Engine OFF" and "Open and Engine OFF" are both 0 MPa, the pressure discharge valve may be stuck open or there may be a fuel leak.

·

Perform "Always Closed Check" if the value is not 0 MPa when the pressure discharge valve is open during "Close to Open Check". If the results are the same as during "Close to Open Check", there is a pressure discharge valve operation malfunction.




Result:
Proceed to
OK
NG



OK

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

3.REPLACE COMMON RAIL ASSEMBLY
3.REPLACE COMMON RAIL ASSEMBLY

Result:
Proceed to
NEXT



NEXT

4.BLEED AIR FROM FUEL SYSTEM
4.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

g.

Confirm that the pending DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P1271 and P1272.


iii.

Check the DTC judgment result.

HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure 3 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.




Result:
Proceed to
NEXT



NEXT

END

6.INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE RESISTANCE)

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - INJECTOR DRIVER)

NG

2.CHECK COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE OPERATION)
7.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - INJECTOR DRIVER)
a.

Disconnect the injector driver connector.


b.

Disconnect the pressure discharge valve connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C99-2 - C43-4 (RLF+) Always Below 1 Ω
C99-1 - C44-1 (RLF-) Always Below 1 Ω
C99-2 or C43-4 (RLF+) - Body ground Always 10 kΩ or higher
C99-1 or C44-1 (RLF-) - Body ground Always 10 kΩ or higher



d.

Reconnect the injector driver connector.


e.

Reconnect the pressure discharge valve connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ECM - INJECTOR DRIVER)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK HARNESS AND CONNECTOR (ECM - INJECTOR DRIVER)
a.

Disconnect the injector driver connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-2 (PRD) - C22-32 (PRD) Always Below 1 Ω
C45-5 (INJF) - C22-25 (INJF) Always Below 1 Ω
C45-2 (PRD) or C22-32 (PRD) - Body ground Always 10 kΩ or higher
C45-5 (INJF) or C22-25 (INJF) - Body ground Always 10 kΩ or higher



d.

Reconnect the injector driver connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

9.INSPECT INJECTOR DRIVER (POWER SOURCE CIRCUIT)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.INSPECT INJECTOR DRIVER (POWER SOURCE CIRCUIT)
a.
A221614
0.51,1.396 0.896,1.656 0.385,0.26 1.677,1.188 1.156,0.844 true 2.427,1.656 1.969,1.271 true 0.563,1.448 0.844,1.604 0.281,0.156 10 false C43 0.74,0.771 1.219,1.094 0.479,0.323 10 false +B (+) 0.167,0.177 0.406,0.469 0.24,0.292 10 false *a 2.469,1.646 3.073,1.948 0.604,0.302 10 false GND (-)
*a Front view of wire harness connector
(to Injector Driver)


Disconnect the injector driver connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C43-2 (+B) - C43-3 (GND) Ignition switch ON 11 to 14 V



c.

Reconnect the injector driver connector.


Result:
Proceed to
OK
NG



OK

10.REPLACE INJECTOR DRIVER

NG

13.GO TO INJECTOR CIRCUIT
10.REPLACE INJECTOR DRIVER
a.

Replace the injector driver.

Click hereEngine / Hybrid System>1KD-FTV FUEL>INJECTOR DRIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CHECK IF DTC OUTPUT RECURS (DTC P1271 AND/OR P1272)
11.CHECK IF DTC OUTPUT RECURS (DTC P1271 AND/OR P1272)
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

g.

Read the pending DTCs.

HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P1271 and P1272.


iii.

Check the DTC judgment result.

Result:
Tester Display Result Proceed to
Pending DTC P1271 and/or P1272 is output B
All Readiness NORMAL A
ABNORMAL B


HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure 3 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.





A

END

B

14.REPLACE ECM
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.GO TO INJECTOR CIRCUIT

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED