When the ignition switch is turned to ON, the battery voltage is applied to terminal IGSW of the ECM. The MREL output signal from ECM causes a current to flow to the coil, closing the contacts of the MAIN relay and supplying power to terminal +B of the ECM.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>INITIALIZATION).
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G39-1 (+B) - C23-7 (E1) | IG ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>PROBLEM SYMPTOMS TABLE
NG
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C23-7 (E1) - Body ground | Always | Below 1 Ω |
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(ECM) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G39-9 (IGSW) - C23-7 (E1) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch to ON.
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G39-8 (MREL) - C23-7 (E1) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 1 integration relay (MAIN relay).
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the harness and connector between the No.1 integration relay (MAIN relay) and ECM.
Remove the integration relay (MAIN relay) from the No. 1 engine room R/B and J/B.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1J-4 - G39-1 (+B) | Always | Below 1 Ω |
| 1J-2 - G39-8 (MREL) | Always | Below 1 Ω |
| 1J-4 or G39-1 (+B) - Body ground | Always | 10 kΩ or higher |
| 1J-2 or G39-8 (MREL) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reinstall the No.1 integration relay.
Check the harness and connector between the integration relay (MAIN relay) and body ground.
Remove the No.1 integration relay (MAIN relay) from the No. 1 engine room R/B and J/B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1J-3 - Body ground | Always | Below 1 Ω |
Reinstall the No.1 integration relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition switch connector.
| *1 | Ignition Switch |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 5 (AM2) - 6 (IG2) | LOCK | 10 kΩ or higher |
| 5 (AM2) - 6 (IG2) | ON | Below 1 Ω |
Reconnect the ignition switch connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG