The mass air flow meter uses a platinum hot wire. The mass air flow meter consists of a platinum hot wire, a temperature sensor and a control circuit installed in a plastic housing. The mass air flow meter works on the principle that the hot wire and temperature sensor located in the intake air by-pass of the housing detect any changes in the intake air temperature.
The hot wire is maintained at the predetermined temperature by controlling the current flow through the hot wire. This current flow is then related as the output voltage of the mass air flow meter.
The circuit is constructed so that the platinum hot wire and temperature sensor provide a bridge circuit, with the power transistor controlled so that the potential of A and B remains equal to maintain the predetermined temperature.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0100 | Mass Air Flow Circuit Malfunction | Mass air flow meter voltage is 0.2 V or less, or 4.9 V or more with the engine speed at 4000 rpm or less for 3 seconds (1 trip detection logic). | ·
Open or short in mass air flow meter circuit ·
Mass air flow meter ·
ECM |
Comes on | DTC stored |
| P0102 | Mass Air Flow Circuit Low | Mass air flow meter voltage is 0.2 V or less with the engine speed at 4000 rpm or less for 3 seconds (1 trip detection logic). | ·
Open or short in mass air flow meter circuit ·
Mass air flow meter ·
ECM |
Comes on | DTC stored |
| P0103 | Mass Air Flow Circuit High | Mass air flow meter voltage is 4.9 V or more with the engine speed at 4000 rpm or less for 3 seconds (1 trip detection logic). | ·
Open or short in Mass air flow meter circuit ·
Mass air flow meter ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0100 | MAF |
| P0102 | |
| P0103 |
If DTC P0102 is stored, the following symptoms may appear (as the ECM mistakenly determines that there is less air than the actual intake air amount, EGR is decreased according to the target EGR):
Combustion noise worsens
If DTC P0103 is stored, the following symptoms may appear (as the ECM mistakenly determines that there is more air than the actual intake air amount, EGR is increased according to the target EGR):
Misfire
White smoke
Black smoke
After confirming DTC P0100, P0102 or P0103, check the mass air flow ratio in the following menus: Powertrain / Engine and ECT / Data List / MAF using the intelligent tester.
| Air Flow Value (gm/s) | Malfunction |
|---|---|
| Approximately 0.0 | ·
Open in mass air flow meter power source circuit ·
Open or short in VG circuit |
| 167.5 or more | Open in EVG circuit |
| DTC Detection Drive Pattern | 3 seconds after engine is started |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *a | Front view of wire harness connector
(to Mass Air Flow Meter) |
Disconnect the mass air flow meter connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C36-1 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
Reconnect the mass air flow meter connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C36-3 - C23-24 (VG) | Always | Below 1 Ω |
| C36-2 - C23-32 (EVG) | Always | Below 1 Ω |
| C36-3 or C23-24 (VG) - Body ground | Always | 10 kΩ or higher |
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the mass air flow meter.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>MASS AIR FLOW METER(w/o Glow Plug Controller)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR
Start the engine and wait for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0100, P0102 and/or P0103 is output | A |
| No DTC is output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR
Start the engine and wait for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the mass air flow meter connector.
Remove the No. 1 integration relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C36-1 - 1J-5 | Always | Below 1 Ω |
| C36-1 or 1J-5 - Body ground | Always | 10 kΩ or higher |
Reconnect the mass air flow meter connector.
Reinstall the No. 1 integration relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the ECM power source circuit.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>ECM Power Source Circuit
| Proceed to |
|---|
| NEXT |
NEXT