Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052103 ECD SYSTEM(w/o EGR Cooler) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P0191  Fuel Rail Pressure Sensor Circuit Range / Performance  


DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the suction control valve to regulate the common rail pressure so that it reaches the target pressure determined by the ECM. The pressure sensor is a semiconductor that varies its electrical resistance when pressure is applied to its silicon chip. This sensor outputs a voltage in proportion to the common rail fuel pressure.

A208460
2.75,0.542 2.906,0.396 2.906,0.396 2.958,0.396 false 3.115,2.188 3.219,2.135 3.219,2.135 3.26,2.135 false 1.969,1.646 2.198,1.646 false 2.24,1.104 2.51,1.104 false 1.406,0.542 0.938,0.656 false 0.073,0.042 1.865,0.302 1.792,0.26 10 false Property of Output Voltage: 1.083,0.417 1.396,0.625 0.313,0.208 10 false 5.00 0.635,0.604 0.99,0.833 0.354,0.229 10 false 4.90 2.24,1.563 3.094,1.833 0.854,0.271 10 false RR2 (Sub) 1.573,1.01 2.313,1.281 0.74,0.271 10 false RR (Main) 1.094,0.646 1.406,0.854 0.313,0.208 10 false 4.44 1.083,0.854 1.417,1.052 0.333,0.198 10 false 3.89 1.083,1.74 1.396,1.896 0.313,0.156 10 false 1.40 1.083,1.927 1.396,2.083 0.313,0.156 10 false 0.85 1.094,2.104 1.406,2.26 0.313,0.156 10 false 0.55 1.281,2.271 1.406,2.427 0.125,0.156 10 false 0 2.958,2.333 3.469,2.563 0.51,0.229 10 false 190000 1.344,2.469 2.698,2.698 1.354,0.229 10 false Fuel Pressure (kPa) 3.281,2.063 4.177,2.302 0.896,0.24 10 false Stores P0192 3.042,0.302 3.99,0.573 0.948,0.271 10 false Stores P0193 0.073,1.188 1.302,1.448 1.229,0.26 10 false Output Voltage (V) 5.198,1.156 5.625,1.385 0.427,0.229 10 false Main 5.25,1.917 5.677,2.115 0.427,0.198 10 false Sub 6.729,1.177 7.063,1.365 0.333,0.188 10 false PR 6.729,1.375 7.042,1.563 0.313,0.188 10 false E2 6.729,1.729 7.083,1.917 0.354,0.188 10 false VCS 6.74,1.938 7.104,2.135 0.365,0.198 10 false PR2 5.896,0.667 6.167,0.906 0.271,0.24 10 false VC 6.365,2.438 6.74,2.646 0.375,0.208 10 false E2S 4.219,0.042 6.729,0.5 2.51,0.458 10 false Internal Structure of the Pressure Sensor (Duplicate Systems):

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0191 Fuel Rail Pressure Sensor Circuit Range / Performance The difference between the main and sub voltage outputs of the fuel pressure sensor is 0.04 V or less, or 1.06 V or higher for 1 second or more (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0191
·

Fuel Press

·

Target Common Rail Pressure



CONFIRMATION DRIVING PATTERN

P0191
DTC Detection Drive Pattern Idling for 1 second

CAUTION / NOTICE / HINT

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.

Powertrain > Engine > Data List
Tester Display
Target Common Rail Pressure
Fuel Press
50003 61 416,54

d.

Start the engine.


e.

Check the change in the values for the Data List items above when increasing the engine speed from idling to 3000 rpm with no load.

Result:
Result Proceed to
Fuel Press is always 10000 kPa or less
or
Fuel Press is always 200000 kPa or higher
A
Except above B


HINT:

Normally, "Fuel Press" is within 15000 kPa of "Target Common Rail Pressure".




A

2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

B

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-5 (PR) - C22-26 (PCR1) Always Below 1 Ω
C16-2 (PR2) - C22-33 (PCR2) Always Below 1 Ω
C16-1 (VCS) - C23-2 (VCS) Always Below 1 Ω
C16-6 (VC) - C22-18 (VC) Always Below 1 Ω
C16-4 (E2) - C22-28 (E2) Always Below 1 Ω
C16-3 (E2S) - C23-1 (E2S) Always Below 1 Ω
C16-5 (PR) or C22-26 (PCR1) - Body ground Always 10 kΩ or higher
C16-2 (PR2) or C22-33 (PCR2) - Body ground Always 10 kΩ or higher
C16-1 (VCS) or C23-2 (VCS) - Body ground Always 10 kΩ or higher
C16-6 (VC) or C22-18 (VC) - Body ground Always 10 kΩ or higher
C16-4 (E2) or C22-28 (E2) - Body ground Always 10 kΩ or higher
C16-3 (E2S) or C23-1 (E2S) - Body ground Always 10 kΩ or higher



d.

Reconnect the fuel pressure sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE COMMON RAIL

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Let the engine idle for 1 second.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

f.

Read the DTCs.

Result:
Result Proceed to
P0191 is output A
No DTC is output B




A

5.REPLACE COMMON RAIL

B

END

5.REPLACE COMMON RAIL

Result:
Proceed to
NEXT



NEXT

6.BLEED AIR FROM FUEL SYSTEM
6.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Let the engine idle for 1 second.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

f.

Read the DTCs.

Result:
Result Proceed to
P0191 is output A
No DTC is output B




A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Let the engine idle for 1 second.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END