The camshaft position sensor (G signal) consists of a magnet, iron core and pickup coil.
The G signal plate (timing pulley) has five teeth on its outer circumference and is installed on the camshaft. When the camshaft rotates, the protrusion on the signal plate and the air gap on the pickup coil change, causing fluctuations in the magnetic field that generate a voltage in the pickup coil.
The NE signal plate has 34 teeth and is mounted on the crankshaft angle sensor plate. The NE signal sensor generates 34 signals for every revolution. The ECM detects the camshaft angle based on the G signal, and detects the crankshaft angle based on the NE signal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0340 | Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) | STA on:
No camshaft position sensor signal is sent to the ECM while cranking for 4 seconds or more (2 trip detection logic). STA off: When either condition below is met a certain number of times (1 trip detection logic): ·
Camshaft position sensor signal is not input with an engine speed of 650 rpm or more. ·
Phase deviation in crankshaft and camshaft position sensor signals with an engine speed of 650 to 3000 rpm. |
·
Open or short in camshaft position sensor circuit ·
Camshaft position sensor ·
Camshaft timing pulley ·
Crank shaft position sensor ·
ECM |
Comes on | DTC stored |
If DTC P0340 is stored, the following symptoms may appear:
Difficulty starting
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
| DTC Detection Drive Pattern | Crank engine for 4 seconds (STA on) |
| Idle engine for 1 second (STA off) |
Refer to DTC P0335 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>P0335).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the camshaft position sensor.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>CAMSHAFT POSITION SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the camshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C7-1 - C23-23 (G+) | Always | Below 1 Ω |
| C7-2 - C23-31 (G-) | Always | Below 1 Ω |
| C7-1 or C23-23 (G+) - Body ground | Always | 10 kΩ or higher |
| C7-2 or C23-31 (G-) - Body ground | Always | 10 kΩ or higher |
Reconnect the camshaft position sensor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the sensor installation.
Sensor is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the condition of the camshaft timing pulley.
Timing pulley does not have any cracks or deformation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR
Turn the ignition switch off and wait for 30 seconds or more.
Start the engine and idle it for 4 seconds or more.
Turn the tester on.
Check the engine condition while wiggling the crankshaft position sensor wire harness for 4 seconds or more when idling.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| Except below | A |
| There are problem such as rough idle or engine stall when wire harness is wiggles, or DTC is output* | B |
*: As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector.
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the camshaft position sensor.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Securely reinstall the sensor.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>CAMSHAFT POSITION SENSOR>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Replace the camshaft timing pulley.
Click hereEngine / Hybrid System>1KD-FTV ENGINE MECHANICAL>ENGINE UNIT(w/o Glow Plug Controller)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR
Turn the ignition switch off for 30 seconds or more.
Start the engine and idle it for 4 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT