Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052103 ECD SYSTEM(w/o EGR Cooler) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P0488  Exhaust Gas Recirculation Throttle Position Control Range / Performance  


DESCRIPTION

The ECM opens and closes the throttle valve using a rotary solenoid type actuator. Due to the opening and closing of the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance The throttle motor activation duty is more than a specified value for 30 seconds (1 trip detection logic).
·

Throttle valve stuck

·

Throttle valve does not move smoothly

·

Open or short in throttle control motor circuit

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0488 Actual Throttle Position

Reference
Condition Throttle Valve Position
Moment when accelerator pedal is depressed further or released at 3000 rpm Throttle valve opening angle varies smoothly

CONFIRMATION DRIVING PATTERN

P0488
DTC Detection Drive Pattern Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.

MONITOR DESCRIPTION

The ECM opens and closes the throttle valve by adjusting the current flowing to the rotary solenoid with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and illuminate the MIL.

A128641
4.604,2.156 4.729,1.833 false 4.594,2.896 4.719,2.573 false 4.604,3.635 4.729,3.323 false 4.74,4.115 4.615,3.802 false 5.313,5.26 5.135,5.042 false 3.333,5.385 3.094,5.208 false 0.333,5.458 1.583,5.844 1.25,0.385 10 false Duty Ratio Malfunction Counter 0.135,0.125 1.917,0.333 1.781,0.208 10 false Malfunction Detection: 0.333,1.365 1.74,1.729 1.406,0.365 10 false Throttle Valve Target Opening Angle 0.292,2.75 1.479,3.188 1.188,0.438 10 false Throttle Valve 0.969,4.167 1.708,4.385 0.74,0.219 10 false Duty Ratio 4.802,1.729 5.396,1.927 0.594,0.198 10 false Normal 4.781,2.5 5.531,2.698 0.75,0.198 10 false Abnormal 4.802,4.031 5.396,4.229 0.594,0.198 10 false Normal 4.781,3.24 5.531,3.438 0.75,0.198 10 false Abnormal 5.948,0.552 6.396,0.75 0.448,0.198 10 false Open 5.948,1.302 6.427,1.5 0.479,0.198 10 false Close 5.948,2.021 6.396,2.219 0.448,0.198 10 false Open 5.948,2.771 6.427,2.969 0.479,0.198 10 false Close 5.948,3.521 6.458,3.729 0.51,0.208 10 false 100% 5.948,4.281 6.292,4.479 0.344,0.198 10 false 0% 3.385,5.323 4.802,5.531 1.417,0.208 10 false Stores P0488 5.365,5.24 6.156,5.448 0.792,0.208 10 false Threshold 3.51,6.271 3.917,6.479 0.406,0.208 10 false Time 0.281,2.917 1.771,3.115 1.49,0.198 10 false Actual Opening Angle

WIRING DIAGRAM

A255067
2.896,1.771 4.344,1.948 1.448,0.177 10 false Throttle Control Motor 2.042,3.552 2.458,3.74 0.417,0.188 10 false MAIN 2.875,3.385 3.167,3.552 0.292,0.167 10 false EFI 2.927,0.542 3.281,0.719 0.354,0.177 10 false RSC 3.469,0.917 3.833,1.073 0.365,0.156 10 false RSO 3.917,3.406 4.552,3.604 0.635,0.198 10 false BATT P/I 3.969,3.896 4.458,4.083 0.49,0.188 10 false Battery 6.146,4.531 6.51,4.698 0.365,0.167 10 false ECM 5.958,0.917 6.375,1.094 0.417,0.177 10 false LUSL 5.958,2.042 6.385,2.219 0.427,0.177 10 false MREL 5.948,2.656 6.156,2.844 0.208,0.188 10 false E1 2.917,1.229 3.188,1.396 0.271,0.167 10 false B 5.615,0.906 5.917,1.083 0.302,0.177 10 false C23 5.604,2.635 5.906,2.813 0.302,0.177 10 false C23 2.896,1.625 3.208,1.792 0.313,0.167 10 false C15 5.594,2.042 5.917,2.219 0.323,0.177 10 false G39 3.865,0.76 3.99,0.958 0.125,0.198 10 false 1 3.083,3.083 3.208,3.281 0.125,0.198 10 false 1 3.51,3.021 3.635,3.219 0.125,0.198 10 false 1 1.344,3.021 1.469,3.219 0.125,0.198 10 false 5 2.75,1.135 2.875,1.323 0.125,0.188 10 false 2 1.344,2.438 1.469,2.625 0.125,0.188 10 false 2 2.823,3.083 2.948,3.271 0.125,0.188 10 false 2 2.75,0.427 2.917,0.615 0.167,0.188 10 false 3 3.51,2.438 3.677,2.625 0.167,0.188 10 false 3 5.698,0.677 5.823,0.854 0.125,0.177 10 false 4 5.698,1.833 5.823,2.01 0.125,0.177 10 false 8 5.698,2.448 5.823,2.625 0.125,0.177 10 false 7 3.458,2.646 3.688,2.823 0.229,0.177 10 false 1J 1.292,2.625 1.521,2.802 0.229,0.177 10 false 1J 1.292,3.24 1.521,3.417 0.229,0.177 10 false 1J 3.458,3.229 3.688,3.406 0.229,0.177 10 false 1H 1.813,4.021 3.344,4.292 1.531,0.271 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).


HINT:
·

Although the DTC titles say exhaust gas recirculation throttle position control Range / Performance, these DTCs relate to the throttle valve

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE)
a.
A129055C03
0.51,1.24 0.938,1.521 0.427,0.281 1.708,1.896 1.708,1.479 true 0.604,1.292 0.917,1.49 0.313,0.198 10 false C15 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.667,1.906 1.979,2.104 0.313,0.198 10 false B
*a Front view of wire harness connector
(to Throttle Control Motor)


Disconnect the throttle control motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C15-2 (B) - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the throttle control motor connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - BATTERY)
2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Disconnect the throttle control motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C15-3 (RSC) - Body ground Always Below 1 Ω



c.

Reconnect the throttle control motor connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)
a.

Disconnect the throttle control motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C15-1 (RSO) - C23-4 (LUSL) Always Below 1 Ω
C15-1 (RSO) or C23-4 (LUSL) - Body ground Always 10 kΩ or higher



d.

Reconnect the throttle control motor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE DIESEL THROTTLE BODY ASSEMBLY

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE DIESEL THROTTLE BODY ASSEMBLY

Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Start the engine.


e.

Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm and lower it.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

g.

Read the DTCs.

Result:
Result Proceed to
P0488 is output A
No DTC is output B




A

6.REPLACE ECM

B

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - BATTERY)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off and wait for 30 seconds or more.


e.

Start the engine.


f.

Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm, and then lower it.


g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0488.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm again, and then idle the engine for 5 minutes.



Result:
Proceed to
NEXT



NEXT

END