Refer to DTC P0046 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>P0046).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1251 | Turbocharger / Supercharger Overboost Condition (Too High) | Boost pressure is higher than the threshold* for 0.5 seconds. (1 trip detection logic). | ·
Turbocharger sub-assembly ·
VN turbo link stuck malfunction ·
Extremely low battery voltage (P0560 stored simultaneously) ·
Intake system ·
Exhaust system ·
Electric EGR control valve assembly ·
Injector assembly ·
Diesel throttle body assembly ·
ECM |
Comes on | DTC stored |
*: This value changes based on engine speed, atmospheric pressure and the engine coolant temperature (the value is generally between 177 and 250 kPa).
| DTC No. | Data List |
|---|---|
| P1251 | ·
MAP ·
Target Booster Pressure ·
MAF ·
Target EGR Position ·
Actual EGR Valve Pos. ·
VN Turbo Command ·
Actual VN Position ·
Atmosphere Pressure |
If DTC P1251 is stored due to the VN turbo vane being stuck closed, the following symptoms may appear:
Vehicle surge when driving with full load
Sudden lack of power due to power being limited
| DTC Detection Drive Pattern | Vehicle being driven |
Refer to DTC P0046 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>P0046).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Record the stored DTC and Freeze Frame Data.
Be sure to carefully examine "MAP" and "Target Booster Pressure" in the freeze frame data.
| Result | Proceed to |
|---|---|
| P1251 is output | A |
| P1251 and other DTCs are output | B |
DC motor-related DTCs: P0046 (See pageEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>P0046), P0047 and P0048 (See pageEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>P0047).
Nozzle vane position sensor-related DTCs: P2563, P2564, P2565, P2588 and P2589 (See pageEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>P2563).
A
B
Check if the hoses between the air cleaner and turbocharger, and turbocharger and intake manifold are damaged or disconnected.
| Result | Proceed to |
|---|---|
| Hoses or pipes are damaged or disconnected | A |
| No hoses or pipes are damaged or disconnected | B |
Be sure to check if the hoses and pipes between the air cleaner and compressor are disconnected as disconnection of a hose or pipe can cause overboost. Also, check the high pressure hoses for disconnection due to overboost.
Check for disconnection of the exhaust pipes.
Using your hand, check whether the pipes and hoses in the intake system are securely connected.
Check for any modifications in the intake system made by the user.
A
B
Repair or replace the malfunctioning part in the air intake system.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON.
Turn the ignition switch off and check the DC motor operation (check the operation link movement).
When it is necessary to repeat this inspection, wait 30 seconds or more with the ignition switch off before performing the inspection.
When ignition switch is turned off, operation link moves as shown in A through D in illustration below.
Operation link and motor rod move smoothly when moving from position shown in A to that shown in B, and from position shown in B to that shown in C.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
| Tester Display |
|---|
| MAF |
Read the MAF value displayed on the tester while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Activate the EGR Valve Close.
| Tester Display |
|---|
| Activate the EGR Valve Close |
Read the MAF value when the EGR valve is closed using the Active Test function.
If idling continues for 15 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or to restart the engine.
Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.
| Active Test | Result | Proceed to |
|---|---|---|
| Activate the EGR Valve Close:
Off (Open) to on (Closed) |
MAF value does not change | A |
| MAF value changes | B |
As the values shown below may differ due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.
The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric vacuum regulating valve assembly or mass air flow meter.
| EGR Valve Condition (Opening) | Measuring Condition | MAF (Reference) |
|---|---|---|
| Open (55%) | ·
Atmosphere pressure: 101 kPa ·
Intake air temperature: 30°C (86°F) ·
Engine coolant temperature: 88°C (190°F) |
3.0 to 9.0 gm/s |
| Close (0%) | 15 to 22 gm/s |
A
B
| *a | Vacuum Hose |
Disconnect the vacuum hose from the electric EGR control valve assembly.
Start the engine.
Check if there is suction from the vacuum hose during idling.
If idling continues for 15 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or to restart the engine.
Suction exists.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EGR VALVE(w/o Glow Plug Controller)>REMOVAL
Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.
If the EGR valve is stuck closed, the intake air amount increases and engine vibration may worsen.
If the EGR valve does not operate due to clogging or disconnection of the vacuum hose, repair the hose.
If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power.
Reinstall the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EGR VALVE(w/o Glow Plug Controller)>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the DC motor connector.
Disconnect the nozzle vane position sensor connector.
Disconnect the turbo motor driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C41-2 (M+) - C39-12 (M+) | Always | Below 1 Ω |
| C41-1 (M-) - C39-5 (M-) | Always | Below 1 Ω |
| C40-1 (VTA1) - C39-9 (VTA1) | Always | Below 1 Ω |
| C40-2 (VNE2) - C39-8 (VNE2) | Always | Below 1 Ω |
| C40-3 (VNVC) - C39-1 (VNVC) | Always | Below 1 Ω |
| C40-4 (VTA2) - C39-10 (VTA2) | Always | Below 1 Ω |
| C40-5 (E2S) - C39-11 (E2S) | Always | Below 1 Ω |
| C40-6 (VCS) - C39-6 (VCS) | Always | Below 1 Ω |
| C41-2 (M+) or C39-12 (M+) - Body ground | Always | 10 kΩ or higher |
| C41-1 (M-) or C39-5 (M-) - Body ground | Always | 10 kΩ or higher |
| C40-1 (VTA1) or C39-9 (VTA1) - Body ground | Always | 10 kΩ or higher |
| C40-2 (VNE2) or C39-8 (VNE2) - Body ground | Always | 10 kΩ or higher |
| C40-3 (VNVC) or C39-1 (VNVC) - Body ground | Always | 10 kΩ or higher |
| C40-4 (VTA2) or C39-10 (VTA2) - Body ground | Always | 10 kΩ or higher |
| C40-5 (E2S) or C39-11 (E2S) - Body ground | Always | 10 kΩ or higher |
| C40-6 (VCS) or C39-6 (VCS) - Body ground | Always | 10 kΩ or higher |
Reconnect the DC motor connector.
Reconnect the nozzle vane position sensor connector.
Reconnect the turbo motor driver connector.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/ TURBOCHARGER(w/o DPF)>INSPECTION
NG
Connect the intelligent tester to the DLC3.
Start the engine and warm it up until the engine coolant temperature reaches 70°C (158°F) or higher.
Allow the engine to idle for 1 minute or more.
The A/C switch and all accessory switches should be off with a fully warm engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Volume.
| Tester Display |
|---|
| Injection Volume |
Read the values during engine idling.
| Result | Proceed to |
|---|---|
| Injection Volume is less than 4 mm3/st | A |
| Except above | B |
If the injector assembly is malfunctioning, the compensatory injection volume remains at 5.0 mm3/st.
If there is a disconnection, the feedback value will increase and +5.0 mm3/st will be indicated, because it will become impossible for the injector to inject.
A
B
Replace the injector assemblies.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR(w/o Glow Plug Controller)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SYSTEM(w/o Glow Plug Controller)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Register the injector compensation code.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION
Perform the injector pilot quantity learning.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR
Turn the ignition switch off.
Remove the EFI fuse from the engine room relay block and junction block assembly for more than 1 minute.
Turn the ignition switch to ON and wait for 10 seconds or more.
Start the engine.
Drive the vehicle with a city driving pattern at least 10 minutes.
Confirm the value of Engine Speed from the Freeze Frame Data recorded previously, and then drive the vehicle according to the Engine Speed value.
Take a snapshot of MAP and Target Boost Pressure in the Data List with the intelligent tester while driving the vehicle.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P1251 is not output and the amount by which MAP exceeds Target Boost Pressure is 20 kPa or less | A |
| Except above | B
* |
*: Return to "Check Air Intake System" and inspect areas that have not been inspected yet.
A
B
Repair or replace of the EGR valve system vacuum hose.
| Proceed to |
|---|
| NEXT |
NEXT