There may be an open circuit in the CAN main wire and/or DLC3 CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or higher.
| Symptom | Trouble Area |
|---|---|
| The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or higher. | ·
CAN main wire and connector ·
No. 1 junction connector ·
No. 2 junction connector ·
No. 3 junction connector ·
ECM ·
DLC3 CAN branch wire or connector |
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
Disconnect the G57 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G57-2 (CANH) - G18-6 (CANH) | Ignition switch off | Below 1 Ω |
| G57-1 (CANL) - G18-14 (CANL) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G57 No. 3 junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
Disconnect the G87 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G87-12 (CANH) - G87-6 (CANL) | Ignition switch off | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G87-4 (CANH) - G87-1 (CANL) | Ignition switch off | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G87 No. 1 junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the G38 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G38-24 (CANH) - G38-23 (CANL) | Ignition switch off | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G87 No. 1 junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
Disconnect the G86 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G86-5 (CANH) - G86-16 (CANL) | Ignition switch off | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G86-6 (CANH) - G86-17 (CANL) | Ignition switch off | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G86 No. 2 junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
Disconnect the G58 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G58-2 (CANH) - G58-1 (CANL) | Ignition switch off | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG