Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(for Built-in Type Door Control Receiver) › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009640 DOOR LOCK _0052678 WIRELESS DOOR LOCK CONTROL SYSTEM(for Built-in Type Door Control Receiver) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(for Built-in Type Door Control Receiver)  Only Wireless Control Function is Inoperative  


DESCRIPTION

The theft warning ECU assembly receives a signal from the door control transmitter assembly and sends these signals to the driver side junction block assembly. The driver side junction block assembly then controls all the doors by sending lock/unlock signals to each door lock assembly.

WIRING DIAGRAM

B258045
5.188,4.26 7.115,4.552 1.927,0.292 10 false Theft Warning ECU Assembly 5.188,4.083 5.49,4.313 0.302,0.229 10 false G29 5.75,0.5 6.333,0.76 0.583,0.26 10 false +B2 5.75,0.969 6.333,1.229 0.583,0.26 10 false +B1 5.75,2.542 6.115,2.76 0.365,0.219 10 false KSW 5.552,2.458 5.698,2.677 0.146,0.219 10 false 5 5.552,3.5 5.698,3.719 0.146,0.219 10 false 1 5.552,0.865 5.698,1.083 0.146,0.219 10 false 4 5.042,2.344 5.188,2.563 0.146,0.219 10 false 1 4.313,2.354 4.458,2.573 0.146,0.219 10 false 2 5.75,1.438 5.948,1.656 0.198,0.219 10 false L2 5.49,1.354 5.688,1.573 0.198,0.219 10 false 25 5.49,0.427 5.688,0.646 0.198,0.219 10 false 14 5.49,1.844 5.688,2.063 0.198,0.219 10 false 26 1.448,1.344 1.646,1.563 0.198,0.219 10 false 14 1.448,1.844 1.646,2.063 0.198,0.219 10 false 11 1.875,1.25 2,1.438 0.125,0.188 10 false 4 5.75,1.938 6.052,2.167 0.302,0.229 10 false UL3 1.167,1.448 1.375,1.667 0.208,0.219 10 false L1 1.833,1.448 2.042,1.667 0.208,0.219 10 false 2A 1.875,1.74 2,1.927 0.125,0.188 10 false 4 1.833,1.938 2.042,2.156 0.208,0.219 10 false 2D 1.073,1.927 1.375,2.125 0.302,0.198 10 false UL1 5.75,3.594 5.917,3.792 0.167,0.198 10 false E 4.417,0.635 4.896,0.833 0.479,0.198 10 false DOOR 4.833,1.104 5.313,1.302 0.479,0.198 10 false ECU-B 4,1.104 4.333,1.302 0.333,0.198 10 false DCC 0.198,3.104 2,3.573 1.802,0.469 10 false Driver Side Junction Block Assembly (Integration Relay) 4.208,3.031 5.323,3.521 1.115,0.49 10 false Unlock Warning Switch Assembly 4.208,2.854 4.51,3.031 0.302,0.177 10 false G10 1.979,2.615 3.5,2.927 1.521,0.313 10 false to Door Lock Assembly 2.219,0.948 3.052,1.177 0.833,0.229 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:

When replacing the theft warning ECU assembly or door control transmitter sub-assembly, refer to the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(for Built-in Type Door Control Receiver)>REGISTRATION).


PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Each door locks and unlocks normally.



Result:
Proceed to
OK
NG



OK

2.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY

NG

2.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY
a.

Check whether the wireless door lock control functions operate normally with another registered door control transmitter assembly.

OK:

Wireless door lock control functions operate normally.



Result:
Proceed to
OK
NG



OK

3.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY (LED)

NG

5.CHECK FOR ELECTRICAL NOISE
3.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY (LED)
a.

Press and hold the lock switch of the door control transmitter assembly for 5 seconds and check the number of times that the transmitter LED illuminates.

Result:
Result Proceed to
Transmitter LED does not illuminate when switch is pressed and held A
Transmitter LED illuminates 3 times or more when switch is pressed and held B
Transmitter LED illuminates once or twice but not third time C




A

4.INSPECT TRANSMITTER BATTERY (VOLTAGE)

B

REPLACE DOOR CONTROL TRANSMITTER SUB-ASSEMBLY

C

REPLACE TRANSMITTER BATTERY

4.INSPECT TRANSMITTER BATTERY (VOLTAGE)
a.
B262355

Remove the transmitter battery from the door control transmitter assembly that does not operate.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT


b.

Attach a lead wire (0.6mm [0.0236 in.] in diameter or less including wire sheath) with tape or equivalent to the negative battery.

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between the terminals or solder it. A terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



c.

Carefully extend the lead wire out from the position shown in the illustration and install the preciously removed transmitter battery.

NOTICE:

When replacing the transmitter battery, before staring work, remove any static electricity that has built up by touching, for example, the vehicle to prevent the door control transmitter sub-assembly from being damaged.



d.

Measure the voltage according to the value(s) in the table below.

HINT:
·

Measure the transmitter battery voltage while pressing the lock or unlock switch on the transmitter.

·

Perform the measurement when the door control transmitter assembly is at room temperature.



Standard Voltage:
Tester Connection Condition Specified Condition
Battery positive (+) - Battery negative (-) Ignition switch off, all doors closed and lock or unlock switch pushed 2.2 to 3.2 V



Result:
Proceed to
OK
NG



OK

REPLACE DOOR CONTROL TRANSMITTER SUB-ASSEMBLY

NG

REPLACE TRANSMITTER BATTERY

5.CHECK FOR ELECTRICAL NOISE
a.

Move the door control transmitter assembly in the vicinity of the theft warning ECU assembly.

HINT:

Refer to Parts Location for the location of the theft warning ECU assembly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(for Built-in Type Door Control Receiver)>PARTS LOCATION



b.

Press and hold either the lock or unlock transmitter switch for 1 second and check that the doors lock or unlock accordingly.

OK:

Wireless door lock control functions operate normally.


HINT:
·

Check if electrical noise is the cause by moving the door control transmitter assembly closer to the theft warning ECU assembly. Moving it closer will decrease the effects of electrical noise.

·

If the operation check can be performed normally, there is a high probability the electrical noise or decrease in output from the door control transmitter assembly is the cause of the malfunction. There is a high probability that electrical noise is the cause if the problem occurs only in a certain location or only during a certain time of day. Also, custom components may be causing electrical noise. If custom components are installed in the vehicle, remove them and perform the operation check again.




Result:
Proceed to
OK
NG



OK

FIND CAUSE OF NOISE AND REMOVE IT

NG

6.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
6.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.
B274206
0.615,1.073 0.802,1.26 0.188,0.188 10 *a 1.229,1.344 1.417,1.531 0.188,0.188 10 *b
*a Pushed
*b Not pushed


Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Not pushed 10 kΩ or higher
Pushed Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - THEFT WARNING ECU AND BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - THEFT WARNING ECU AND BODY GROUND)
a.

Disconnect the G10 unlock warning switch assembly connector.


b.

Disconnect the G29 theft warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G10-1 - G29-5 (KSW) Always Below 1 Ω
G10-1 or G29-5 (KSW) - Body ground Always 10 kΩ or higher
G10-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - DRIVER SIDE JUNCTION BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - DRIVER SIDE JUNCTION BLOCK)
a.

Disconnect the G29 theft warning ECU assembly connector.


b.

Disconnect the 2A and 2D driver side junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G29-25 (L2) - 2A-4 (L1) Always Below 1 Ω
G29-26 (UL3) - 2D-4 (UL1) Always Below 1 Ω
G29-25 (L2) or 2A-4 (L1) - Body ground Always 10 kΩ or higher
G29-26 (UL3) or 2D-4 (UL1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - BATTERY AND BODY GROUND)
a.
B274165
0.104,1.115 0.688,1.458 0.583,0.344 0.875,1.208 0.604,0.917 0.604,0.917 0.458,0.917 true 1.271,1.208 1.125,0.635 1.125,0.635 0.958,0.635 true 2.521,1.198 2.646,0.792 2.646,0.792 2.823,0.792 true 0.063,0.052 0.24,0.25 0.177,0.198 10 *a 0.25,1.198 0.531,1.365 0.281,0.167 10 G29 2.844,0.698 3.135,0.885 0.292,0.188 10 +B2 0.667,0.552 0.948,0.74 0.281,0.188 10 +B1 0.333,0.833 0.448,0.99 0.115,0.156 10 E
*a Front view of wire harness connector
(to Theft Warning ECU Assembly)


Disconnect the G29 theft warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G29-1 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G29-4 (+B1) - Body ground Always 11 to 14 V
G29-14 (+B2) - Body ground Always



Result:
Proceed to
OK
NG



OK

10.REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Temporarily replace the driver side junction block assembly with a new or normally functioning one.


b.

Check that the wireless door lock control functions.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(for Built-in Type Door Control Receiver)>OPERATION CHECK

OK:

Wireless door lock control functions operate normally.



Result:
Proceed to
OK
NG



OK

END (DRIVER SIDE JUNCTION BLOCK IS DEFECTIVE)

NG