The driver side squib circuit consists of the center airbag sensor, spiral cable and steering pad.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the driver side squib circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1800/51 | Short in Driver Side Squib Circuit | One of the following conditions is met:
·
The center airbag sensor detects a line short circuit signal 5 times in the driver side squib circuit during the primary check. ·
A driver side squib malfunction. ·
A spiral cable malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Spiral cable sub-assembly ·
Steering pad (Driver side squib) ·
Center airbag sensor assembly |
DTC is output in check mode. |
| B1801/51 | Open in Driver Side Squib Circuit | One of the following conditions is met:
·
The center airbag sensor detects an open circuit signal in the driver side squib circuit for 2 seconds. ·
A driver side squib malfunction. ·
A spiral cable malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Spiral cable sub-assembly ·
Steering pad (Driver side squib) ·
Center airbag sensor assembly |
DTC is output in check mode. |
| B1802/51 | Short to GND in Driver Side Squib Circuit | One of the following conditions is met:
·
The center airbag sensor detects a short circuit to ground signal in the driver side squib circuit for 0.5 seconds. ·
A driver side squib malfunction. ·
A spiral cable malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Spiral cable sub-assembly ·
Steering pad (Driver side squib) ·
Center airbag sensor assembly |
DTC is output in check mode. |
| B1803/51 | Short to B+ in Driver Side Squib Circuit | One of the following conditions is met:
·
The center airbag sensor detects a short circuit to B+ signal in the driver side squib circuit for 0.5 seconds. ·
A driver side squib malfunction. ·
A spiral cable malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Spiral cable sub-assembly ·
Steering pad (Driver side squib) ·
Center airbag sensor assembly |
DTC is output in check mode. |
When installing the spiral cable and steering wheel, be sure to adjust the spiral cable as it may break if the steering wheel is turned before adjusting the spiral cable (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
| *1 | Driver Side Squib |
| *2 | Spiral Cable |
| *3 | Center Airbag Sensor |
| *4 | Connector E |
| *5 | SST |
| *a | Front view of wire harness connector
(to Driver Side Squib) |
| *b | Color: Orange |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the steering pad.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).
Never connect the tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.
Codes other than DTC B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector E.
Disconnect the connectors from the center airbag sensor.
| *1 | Driver Side Squib |
| *2 | Spiral Cable |
| *3 | Center Airbag Sensor |
Check that the connectors (on the center airbag sensor side and steering pad side) are not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Driver Side Squib |
| *2 | Spiral Cable |
| *3 | Center Airbag Sensor |
| *4 | Connector E |
| *a | Front view of wire harness connector
(to Driver Side Squib) |
| *b | Color: Orange |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 2 (D+) - Body ground | Ignition switch ON | Below 1 V |
| 1 (D-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (D+) - 1 (D-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (D+) - 1 (D-) | Always | 1 MΩ or higher |
| 2 (D+) - Body ground | Always | 1 MΩ or higher |
| 1 (D-) - Body ground | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Driver Side Squib |
| *2 | Spiral Cable |
| *3 | Center Airbag Sensor |
Connect the connectors to the steering pad and center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.
Codes other than DTC B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Instrument Panel Wire |
| *2 | Spiral Cable |
| *3 | Center Airbag Sensor |
| *4 | Connector C |
| *a | Rear view of wire harness connector
(to Spiral Cable) |
Disconnect the instrument panel wire connector from the spiral cable.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G52-1 (D+) - Body ground | Ignition switch ON | Below 1 V |
| G52-2 (D-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G52-1 (D+) - G52-2 (D-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G52-1 (D+) - G52-2 (D-) | Always | 1 MΩ or higher |
| G52-1 (D+) - Body ground | Always | 1 MΩ or higher |
| G52-2 (D-) - Body ground | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG