Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009645 SUPPLEMENTAL RESTRAINT SYSTEMS _0052709 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1900/73  Short in Front Driver Side Pretensioner Squib Circuit  B1901/73  Open in Front Driver Side Pretensioner Squib Circuit  B1902/73  Short to GND in Front Driver Side Pretensioner Squib Circuit  B1903/73  Short to B+ in Front Driver Side Pretensioner Squib Circuit  


DESCRIPTION

The front pretensioner squib circuit consists of the center airbag sensor and front seat outer belt assembly LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front seat outer belt assembly LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1900/73 Short in Front Driver Side Pretensioner Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the front seat outer belt assembly LH circuit during the primary check.

·

A front seat outer belt assembly LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat outer belt assembly LH

·

Center airbag sensor assembly


DTC is output in check mode
B1901/73 Open in Front Driver Side Pretensioner Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects an open circuit signal in the front seat outer belt assembly LH circuit for 2 seconds.

·

A front seat outer belt assembly LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat outer belt assembly LH

·

Center airbag sensor assembly


DTC is output in check mode
B1902/73 Short to GND in Front Driver Side Pretensioner Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the front seat outer belt assembly LH circuit for 0.5 seconds.

·

A front seat outer belt assembly LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat outer belt assembly LH

·

Center airbag sensor assembly


DTC is output in check mode
B1903/73 Short to B+ in Front Driver Side Pretensioner Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the front seat outer belt assembly LH circuit for 0.5 seconds.

·

A front seat outer belt assembly LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat outer belt assembly LH

·

Center airbag sensor assembly


DTC is output in check mode

WIRING DIAGRAM

C247622
0.74,3.188 3.135,3.427 2.396,0.24 10 false Front Seat Outer Belt Assembly LH 2.188,1.563 2.365,1.75 0.177,0.188 10 false L+ 2.219,2.385 2.365,2.573 0.146,0.188 10 false L- 4.792,1.677 5.188,1.865 0.396,0.188 10 false PD+ 4.802,2.521 5.198,2.708 0.396,0.188 10 false PD- 2.469,1.552 2.615,1.719 0.146,0.167 10 false 1 2.479,2.385 2.635,2.542 0.156,0.156 10 false 2 4.552,1.573 4.667,1.74 0.115,0.167 10 false 2 4.552,2.406 4.677,2.573 0.125,0.167 10 false 1 4.76,4.177 5.083,4.365 0.323,0.188 10 false K38 4.75,4.323 6.281,4.552 1.531,0.229 10 false Center Airbag Sensor 0.74,3.031 1.792,3.188 1.052,0.156 10 false K41

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH
a.
C205411
0.333,2.24 0.76,2.521 0.427,0.281 2.083,2.354 2.448,2.635 false 0.802,0.573 1.115,0.771 0.313,0.198 10 false *1 1.021,1.083 1.177,1.302 0.156,0.219 10 false D 1.24,1.083 1.396,1.302 0.156,0.219 10 false C 2.135,1.448 2.448,1.646 0.313,0.198 10 false *2 1.563,1.76 1.875,1.958 0.313,0.198 10 false *a 2.385,2.198 2.698,2.396 0.313,0.198 10 false *3 2.5,2.563 2.896,2.76 0.396,0.198 10 false SST 0.427,2.292 0.823,2.49 0.396,0.198 10 false K41
*1 Front Seat Outer Belt Assembly LH
*2 Center Airbag Sensor
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front seat outer belt assembly LH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assemblyLH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTC.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 63

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 63
OK:

DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.


HINT:

Codes other than DTC B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Disconnect the connectors from the center airbag sensor.


e.
C208251C06
0.646,0.792 0.875,0.969 0.229,0.177 10 false *1 1.271,0.781 1.5,0.958 0.229,0.177 10 false *2 0.865,1.281 1.094,1.458 0.229,0.177 10 false D 1.094,1.281 1.323,1.458 0.229,0.177 10 false C 1.906,1 2.135,1.177 0.229,0.177 10 false A 1.729,1.656 1.958,1.833 0.229,0.177 10 false *3 1.49,1.281 1.719,1.458 0.229,0.177 10 false B
*1 Front Pretensioner Squib RH
*2 Center Airbag Sensor
*3 *2


Check that the connectors (on the center airbag sensor side and front seat outer belt assembly LH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Result
OK
NG



OK

3.CHECK NO. 2 FLOOR WIRE (FRONT SEAT OUTER BELT ASSEMBLY LH)

NG

REPLACE NO. 2 FLOOR WIRE

3.CHECK NO. 2 FLOOR WIRE (FRONT SEAT OUTER BELT ASSEMBLY LH)
a.
C205412
0.385,2.198 0.75,2.469 0.365,0.271 1.24,2.771 1.656,2.354 true 2.146,2.771 1.792,2.354 true 0.75,0.563 1.063,0.76 0.313,0.198 10 false *1 1.344,0.563 1.656,0.76 0.313,0.198 10 false *2 2.219,1.438 2.531,1.635 0.313,0.198 10 false *3 0.948,1.063 1.125,1.26 0.177,0.198 10 false D 1.167,1.063 1.344,1.26 0.177,0.198 10 false C 1.542,1.063 1.719,1.26 0.177,0.198 10 false B 1.969,0.792 2.146,0.99 0.177,0.198 10 false A 1.646,1.833 1.854,2.052 0.208,0.219 10 false *a 2.427,2.115 2.635,2.333 0.208,0.219 10 false *4 2.177,2.792 2.385,3.01 0.208,0.219 10 false L- 1.167,2.792 1.375,3.01 0.208,0.219 10 false L+ 0.458,2.25 0.917,2.448 0.458,0.198 10 false K41
*1 Front Seat Outer Belt Assembly LH
*2 No. 2 Floor Wire
*3 Center Airbag Sensor
*4 Connector C
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K41-1 (L+) - Body ground Ignition switch ON Below 1 V
K41-2 (L-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K41-1 (L+) - K41-2 (L-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K41-1 (L+) - K41-2 (L-) Always 1 MΩ or higher
K41-1 (L+) - Body ground Always 1 MΩ or higher
K41-2 (L-) - Body ground Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Result
OK
NG



OK

4.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK CENTER AIRBAG SENSOR
a.
C146261
0.802,1.104 0.802,1.49 false 0.708,1.5 0.906,1.698 0.198,0.198 10 false *1 0.979,1.188 1.115,1.448 0.135,0.26 10 false D 1.104,1.188 1.25,1.375 0.146,0.188 10 false C 1.479,1.469 1.677,1.635 0.198,0.167 10 false *2
*1 Front Pretensioner Squib RH
*2 Center Airbag Sensor


Connect the connectors to the front seat outer belt assembly LH and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 63

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 63
OK:

DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.


HINT:

Codes other than DTC B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.



Result:
Result
OK
NG



OK

NG