Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2012.01–2012.04
RM1840EF _58 Vehicle Interior _009645 SUPPLEMENTAL RESTRAINT SYSTEMS _0052709 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3. The DTCs are communicated through SRS warning light blinking patterns.

HINT:

When one or more of the warning lights blink continuously, the cause may be a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in an ECU.


WIRING DIAGRAM

C240459
5.49,2.771 6.896,2.99 1.406,0.219 10 Center Airbag Sensor 5.802,1.146 6.115,1.333 0.313,0.188 10 TC 0.958,2.292 1.323,2.438 0.365,0.146 10 G18 0.958,2.469 1.375,2.635 0.417,0.167 10 DLC3 1.573,1.146 1.885,1.333 0.313,0.188 10 TC 1.563,1.917 1.865,2.125 0.302,0.208 10 CG 5.552,1.052 5.865,1.24 0.313,0.188 10 15 1.844,1.063 2.156,1.25 0.313,0.188 10 13 1.854,1.792 2.167,1.979 0.313,0.188 10 4 5.5,2.573 5.813,2.76 0.313,0.188 10 G53

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DLC3 - CENTER AIRBAG SENSOR AND BODY GROUND)
a.
C237254
1.521,0.073 1.938,0.344 0.417,0.271 1.521,1.573 1.938,1.844 0.417,0.271 0.667,1.167 1.615,0.813 true 1.823,1.167 2.75,1.385 true 1.781,2.542 2.594,2.771 true 0.083,0.042 0.281,0.25 0.198,0.208 10 false *a 0.083,1.51 0.281,1.719 0.198,0.208 10 false *b 0.396,1.115 0.646,1.26 0.25,0.146 10 false CG 2.802,1.323 3.052,1.469 0.25,0.146 10 false TC 2.625,2.708 2.885,2.865 0.26,0.156 10 false TC 1.604,0.125 1.906,0.302 0.302,0.177 10 false G18 1.604,1.635 1.906,1.813 0.302,0.177 10 false G53
*a Front view of DLC3
*b Rear view of wire harness connector
(to Center Airbag Sensor)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the G53 connector from the center airbag sensor.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G18-13 (TC) - G53-15 (TC) Always Below 1 Ω
G18-4 (CG) - Body ground Always Below 1 Ω
G53-15 (TC) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR