Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) › 2012.04–2012.10
RM1840EF _59 Vehicle Exterior _009651 WINDOW / GLASS _0052778 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  Auto Up / Down Function does not Operate  


DESCRIPTION

If the auto up/down function does not operate, the cause may be one or more of the following:

·

The recorded power window fully closed position, which is stored in the power window regulator master switch assembly, was erased as a result of: 1) the PWR H-fuse or DOOR fuse being replaced; or 2) the battery cable and the master switch's connector being disconnected.

·

The power window regulator master switch assembly has a malfunction.

·

The pulse sensors in the front power window regulator motor assembly LH have a malfunction.

·

The wiring between the power window regulator master switch assembly and the front power window regulator motor assembly RH is open or short-circuited.


WIRING DIAGRAM

B276696
5.406,2.813 6.958,3.271 1.552,0.458 10 false Power Window Regulator Master Switch Assembly 0.292,2.917 2.188,3.406 1.896,0.49 10 false Front Power Window Regulator Motor Assembly LH 0.906,1.188 1.24,1.354 0.333,0.167 10 false PLS 5.635,0.688 6.083,0.938 0.448,0.25 10 false VCC 5.646,1.198 6.083,1.458 0.438,0.26 10 false PLS 5.646,1.677 6.094,1.896 0.448,0.219 10 false PLS2 5.646,2.177 6.01,2.375 0.365,0.198 10 false GND 0.583,1.698 0.917,1.865 0.333,0.167 10 false PLS 1.76,0.563 1.885,0.75 0.125,0.188 10 false 4 1.76,1.083 1.906,1.24 0.146,0.156 10 false 5 1.76,1.594 1.885,1.781 0.125,0.188 10 false 3 1.76,2.104 1.885,2.292 0.125,0.188 10 false 6 1.271,0.802 1.688,0.979 0.417,0.177 10 false SSRB 1.385,1.302 1.719,1.479 0.333,0.177 10 false PLS 1.313,1.823 1.729,2 0.417,0.177 10 false PLS2 1.531,2.323 1.677,2.5 0.146,0.177 10 false E 5.458,0.573 5.615,0.75 0.156,0.177 10 false 3 5.396,1.083 5.594,1.24 0.198,0.156 10 false 14 5.385,1.594 5.594,1.75 0.208,0.156 10 false 17 5.469,2.104 5.604,2.25 0.135,0.146 10 false 2 0.292,2.76 0.563,2.948 0.271,0.188 10 false I3 5.396,2.646 5.677,2.823 0.281,0.177 10 false I5

PROCEDURE

1.CHECK MANUAL UP/DOWN FUNCTION (FOR DRIVER SIDE)
a.

Check that the manual up/down function operates normally.

OK:

Manual up/down function operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK LIGHT OF POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

2.CHECK LIGHT OF POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B295638
1.177,0.865 0.792,0.646 false 0.604,0.521 0.844,0.74 0.24,0.219 10 false *1
*1 AUTO Light


Turn the ignition switch to ON.


b.

Operate the master switch's driver side power window switch for 2 seconds or more.


c.

Check the blinking pattern of the AUTO light. Compare the blinking pattern with the illustration.

B278579
0.135,1.229 0.594,1.448 0.458,0.219 10 false ON 0.135,1.51 0.74,1.74 0.604,0.229 10 false OFF 0.135,1.729 0.74,1.938 0.604,0.208 10 false (Light) 1.573,1.802 2,2.01 0.427,0.208 10 false (sec.) 3.083,1.719 3.688,1.927 0.604,0.208 10 false (sec.) 4.708,1.823 5.313,2.031 0.604,0.208 10 false (sec.) 0.135,0.146 2.198,0.385 2.063,0.24 10 false Blinking Pattern of AUTO Light 0.771,0.625 2.344,1.063 1.573,0.438 10 false 1: Fully closed position is misaligned 2.51,0.625 3.906,1.083 1.396,0.458 10 false 2: Pulse sensor circuit malfunction 4.125,0.625 5.167,0.844 1.042,0.219 10 false 3: Both 1 and 2 6.052,0.625 6.885,0.844 0.833,0.219 10 false 4: Normal 1.156,1.625 1.427,1.823 0.271,0.198 10 false 1.5 4.302,1.583 4.625,1.781 0.323,0.198 10 false 1.5 1.208,1.823 1.458,2.021 0.25,0.198 10 false 2.0 4.375,1.802 4.698,2 0.323,0.198 10 false 2.0 3.76,1.792 4,1.99 0.24,0.198 10 false 1.0 2.729,1.823 2.969,2.021 0.24,0.198 10 false 1.0 2.438,1.625 2.76,1.823 0.323,0.198 10 false 0.5 4.031,2.281 4.271,2.469 0.24,0.188 10 false 0.5

Result:
Blinking Pattern Proceed to
1or3 A
2 B
4 C




A

3.RESET FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

C

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

3.RESET FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Check that the power window operates normally after reset.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION

OK:

Power window operates normally.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the I5 power window regulator master switch assembly connector.


b.

Disconnect the I3 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-3 (VCC) - I3-4 (SSRB) Always Below 1 Ω
I5-14 (PLS) - I3-5 (PLS) Always Below 1 Ω
I5-17 (PLS2) - I3-3 (PLS2) Always Below 1 Ω
I5-2 (GND) - I3-6 (E) Always Below 1 Ω
I5-3 (VCC) or I3-4 (SSRB) - Body ground Always 10 kΩ or higher
I5-14 (PLS) or I3-5 (PLS) - Body ground Always 10 kΩ or higher
I5-17 (PLS2) or I3-3 (PLS2) - Body ground Always 10 kΩ or higher



Result:
Proced to
OK
NG



OK

5.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (PLS, PLS2 SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (PLS, PLS2 SIGNAL)
a.
B276285
0.135,0.896 0.667,1.188 0.531,0.292 1.729,0.938 1.51,0.219 true 2.292,1.021 2.75,1.198 true 1.51,0.208 1.646,0.208 false 1.688,0.135 2.031,0.292 0.344,0.156 10 false PLS 0.115,0.115 0.375,0.385 0.26,0.271 10 false *a 2.792,1.135 3.198,1.313 0.406,0.177 10 false PLS2 0.333,0.958 0.563,1.125 0.229,0.167 10 false I5
*a Component with harness connected
(Power Window Regulator Master Switch Assembly)


Remove the power window regulator master switch assembly with its connectors still connected.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Specified Condition
I5-14 (PLS) - Body ground Ignition switch ON, driver side power window switch off → up or down Pulse waveform is output
I5-17 (PLS2) - Body ground



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY