Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009648 HEATING / AIR CONDITIONING _0052762 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  41  Front Air Mix Damper Control Servo Motor Circuit  


DESCRIPTION

The air mix damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the air mix control damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air mix control damper to any position. As a result, the air mix control damper varies the mixture of hot air from the heater core and cold air from the evaporator so that the temperature of the air blowing toward the driver and front passenger side is as requested.

HINT:

This DTC is also output if the damper and damper link are malfunctioning or unable to move properly. When this DTC is output, confirm that the mechanical parts of the damper and damper link are not defective or damaged.


DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
41 Front Air Mix Damper Control Servo Motor Circuit The air mix control damper position does not change when the air conditioning amplifier assembly operates the air mix damper servo sub-assembly.
·

Air mix damper servo sub-assembly

·

Air conditioning amplifier assembly

·

Harness or connector


Memorized
(30 sec. or more)
-

WIRING DIAGRAM

E233156E09
5.323,0.917 5.625,1.063 0.302,0.146 10 false G95 1.75,0.802 1.865,0.948 0.115,0.146 10 false 2 1.74,1.313 1.854,1.458 0.115,0.146 10 false 3 1.729,1.875 1.844,2.021 0.115,0.146 10 false 1 1.74,2.396 1.854,2.542 0.115,0.146 10 false 5 1.729,2.917 1.844,3.063 0.115,0.146 10 false 4 5.333,1.438 5.635,1.583 0.302,0.146 10 false G95 5.396,1.25 5.573,1.396 0.177,0.146 10 false 23 5.396,0.719 5.573,0.865 0.177,0.146 10 false 24 5.323,1.969 5.625,2.115 0.302,0.146 10 false G95 5.385,1.76 5.563,1.906 0.177,0.146 10 false 20 5.333,2.5 5.635,2.646 0.302,0.146 10 false G94 5.396,2.302 5.583,2.448 0.188,0.146 10 false 17 5.333,3.021 5.635,3.167 0.302,0.146 10 false G94 5.365,2.844 5.552,2.99 0.188,0.146 10 false 19 5.688,0.906 6.01,1.073 0.323,0.167 10 false PMA 0.219,3.438 0.552,3.604 0.333,0.167 10 false G81 5.677,1.448 6,1.625 0.323,0.177 10 false PMB 5.677,2 6.042,2.177 0.365,0.177 10 false SG-1 5.688,2.51 6.031,2.688 0.344,0.177 10 false AMH 5.688,3.021 6.031,3.188 0.344,0.167 10 false AMC 1.354,0.823 1.708,0.99 0.354,0.167 10 false MCP 1.344,1.344 1.677,1.521 0.333,0.177 10 false MHP 1.438,1.885 1.698,2.063 0.26,0.177 10 false SG 1.344,2.396 1.688,2.573 0.344,0.177 10 false MHD 1.344,2.917 1.688,3.083 0.344,0.167 10 false MCD 5.365,3.469 6.99,4.073 1.625,0.604 10 false Air Conditioning Amplifier Assembly 0.198,3.615 2.552,3.854 2.354,0.24 10 false Air Mix Damper Servo Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

When DTC 41, 42 and 43 are output at same time, there would be malfunctioning on power source circuit.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>Back-up Power Source Circuit


PROCEDURE

1.PERFORM ACTUATOR CHECK
a.

Warm up the engine.



c.

Place your hand in front of a vent and check that the air mix control damper position changes (the temperature of the air changes) according to the display code.

Display Code Air Mix Control Damper Position
0 COLD side (0% open)
1 COLD side (0% open)
2 COLD side (0% open)
3 COLD side (0% open)
4 COLD/HOT (50% open)
5 COLD/HOT (50% open)
6 HOT side (100% open)
7 HOT side (100% open)
8 HOT side (100% open)
9 HOT side (100% open)

OK:

Air mix control damper position changes in accordance with each display code.


HINT:

The progression through the steps of the actuator check can be changed from automatic to manual by pressing the front DEF switch.


Result:
Result Proceed to
OK (When troubleshooting according to problem symptoms table.) A
OK (When troubleshooting according to DTC.) B
NG C




A

B

C

2.CHECK HARNESS AND CONNECTOR (AIR MIX DAMPER SERVO - AIR CONDITIONING AMPLIFIER)
2.CHECK HARNESS AND CONNECTOR (AIR MIX DAMPER SERVO - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the G81 air mix damper servo sub-assembly connector.


b.

Disconnect the G94 and G95 air conditioning amplifier assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G81-5 (MHD) - G94-17 (AMH) Always Below 1 Ω
G81-4 (MCD) - G94-19 (AMC)
G81-3 (MHP) - G95-23 (PMB)
G81-2 (MCP) - G95-24 (PMA)
G81-1 (SG) - G95-20 (SG-1)
G81-1 (SG) - Body ground Always 10 kΩ or higher
G81-2 (MCP) - Body ground
G81-3 (MHP) - Body ground
G81-4 (MCD) - Body ground
G81-5 (MHD) - Body ground



Result:
Proceed to
OK
NG



OK

3.REPLACE AIR MIX DAMPER SERVO SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE AIR MIX DAMPER SERVO SUB-ASSEMBLY
a.

Temporally replace the air mix damper servo sub-assembly with a new or normally functioning one.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY


b.

Check the air mix control damper operates normally.

OK:

Air mix control damper operates normally.



Result:
Proceed to
OK
NG



OK

END (AIR MIX DAMPER SERVO IS DEFECTIVE)

NG