The manifold absolute pressure sensor detects the intake manifold pressure. The ECM determines the basic injection volume and injection advance timing based on the voltage output by the manifold absolute pressure sensor.
The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa [0 mmHg, 0 in.Hg]). As a result, the ECM controls the air-fuel ratio so that it reaches the proper level under any driving conditions.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0107 | Manifold Absolute Pressure / Barometric Pressure Circuit Low Input | After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 0.1 V or less. |
·
Open or short in manifold absolute pressure sensor circuit ·
Manifold absolute pressure sensor ·
ECM |
Comes on | DTC stored |
| P0108 | Manifold Absolute Pressure / Barometric Pressure Circuit High Input | After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 4.8 V or higher. |
·
Open or short in manifold absolute pressure sensor circuit ·
Manifold absolute pressure sensor ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0107 | ·
MAP ·
Atmosphere Pressure |
| P0108 |
If DTC P0107 and/or P0108 is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
When DTC P0107 or P0108 is stored, check the intake manifold pressure by entering the following menus: Powertrain / Engine and ECT / Data List / MAP.
| Intake Manifold Pressure | Malfunction |
|---|---|
| Approximately 0 kPa | ·
Open in VC circuit ·
Short in PIM circuit |
| 250 kPa (1875 mmHg, 73.8 in.Hg) or higher | ·
Open in PIM circuit ·
Open in E circuit |
| DTC Detection Drive Pattern | 2 seconds after engine is started, race engine for 1 second |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.
| Tester Display |
|---|
| MAP |
Read the value.
Same as the actual atmospheric pressure.
Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather (high atmospheric pressure, low atmospheric pressure).
Also, check "Atmosphere Pressure" in the Data List.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the manifold absolute pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C20-2 (PIM) - C114-5 (PIM) | Always | Below 1 Ω |
| C20-3 (VC) - C114-13 (VC) | Always | Below 1 Ω |
| C20-1 (E) - C114-14 (E2) | Always | Below 1 Ω |
| C20-2 (PIM) or C114-5 (PIM) - Body ground | Always | 10 kΩ or higher |
| C20-3 (VC) or C114-13 (VC) - Body ground | Always | 10 kΩ or higher |
Reconnect the manifold absolute pressure sensor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Absolute Pressure Sensor) |
Disconnect the manifold absolute pressure sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C20-3 (VC) - C20-1 (E) | Ignition switch ON | 4.75 to 5.25 V |
Reconnect the manifold absolute pressure sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the manifold absolute pressure sensor.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR
Turn the ignition switch off for 30 seconds or more.
Turn the tester off.
Start the engine.
After the engine is started for 2 seconds, race the engine for 1 second.
Turn the tester on.
Confirm that the DTC is not output again.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P0107 or P0108.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| ABNORMAL | A |
| NORMAL | B |
If STATUS is INCOMPLETE or N/A, race the engine for 1 minute, and then idle the engine for 5 minutes.
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR
Turn the ignition switch off for 30 seconds or more.
Turn the tester off.
Turn the ignition switch to ON for 3 seconds and turn the tester on.
After the engine is started for 2 seconds, race the engine for 1 second.
Confirm that the DTC is not output again.
Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P0107 or P0108.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine for 1 minute, and then idle the engine for 5 minutes.
| Proceed to |
|---|
| NEXT |
NEXT