Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0489  Exhaust Gas Recirculation Control Circuit Low  P0490  Exhaust Gas Recirculation Control Circuit High  


DESCRIPTION

The EGR actuator is operated by the ECM and opens and closes the EGR valve using gears. The opening angle of the EGR valve is detected by the EGR position sensor, which is mounted on the EGR body.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0489 Exhaust Gas Recirculation Control Circuit Low The EGR actuator current is below 0.5 A for 2.0 seconds during EGR valve operation.
(1 trip detection logic).
·

Open or short in electric EGR control valve assembly circuit

·

Electric EGR control valve assembly

·

ECM


Comes on DTC stored
P0490 Exhaust Gas Recirculation Control Circuit High An EGR actuator current of 8 A or higher due to a mechanical malfunction, or a Hall IC temperature of 150 to 160°C (302 to 320°F) or higher is detected.
(1 trip detection logic):
·

Open or short in electric EGR control valve assembly circuit

·

Electric EGR control valve assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0489
·

Actual EGR Valve Pos.

·

Target EGR Position


P0490

CONFIRMATION DRIVING PATTERN

P0489, P0490
DTC Detection Drive Pattern Idle the engine for 5 seconds or more

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT ELECTRIC EGR VALVE ASSEMBLY

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ELECTRIC EGR VALVE ASSEMBLY - ECM)

NG

4.REPLACE ELECTRIC EGR VALVE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (ELECTRIC EGR VALVE ASSEMBLY - ECM)
a.

Disconnect the electric EGR valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C120-4 (M+) - C112-6 (EGM+) Always Below 1 Ω
C120-5 (M-) - C112-7 (EGM-) Always Below 1 Ω
C120-4 (M+) or C112-6 (EGM+) - Body ground Always 10 kΩ or higher
C120-5 (M-) or C112-7 (EGM-) - Body ground Always 10 kΩ or higher



d.

Reconnect the electric EGR valve assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE ELECTRIC EGR VALVE ASSEMBLY

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

Idle the engine for 5 seconds or more


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END