Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P052F  Glow Plug Control Module System Voltage  P0683  Glow Plug Control Module to PCM Communication Circuit  


DESCRIPTION

The glow system consists of the glow plug controller, glow plugs and ECM. The glow plug controller turns on the glow plug of each cylinder according to the duty command signal from the ECM in order to maintain optimal engine temperatures. The glow plugs can be controlled according to the engine coolant temperature at engine start by using duty signals. This helps induce ignition under low temperatures and prevent rough idle after starting the engine.

The glow plugs are turned on during PM forced regeneration in order to prevent the engine speed from rising due to an increase in fuel injection volume used to increase the exhaust gas temperature. The glow plug controller contains a self-diagnosis function. When the glow plug controller detects an internal malfunction, it sends a signal indicating the malfunction to the ECM. When the ECM receives this signal, it illuminates the MIL and stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P052F Glow Plug Control Module System Voltage The glow plug controller recognizes the battery voltage as being 18.4 V or higher 3 times or more when the glow plugs are on (2 trip detection logic). Glow plug controller Comes on DTC stored
P0683 Glow Plug Control Module to PCM Communication Circuit When the glow plugs are on, the ECM detects that there is no output from the glow plug control unit for 3 seconds even though the ECM outputs an SI signal ("ON" command signal) (1 trip detection logic).
·

Open or short circuit in ground wire

·

Open or short circuit in battery wire

·

Open in SI wire

·

SI wire short circuit to ground or battery

·

Open in DI wire

·

DI wire short circuit to ground or battery

·

Low battery voltage

·

Glow plug controller

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P052F, P0683
DTC Detection Drive Pattern Enter check mode

WIRING DIAGRAM

A276471
2.823,7.146 4.385,7.417 1.563,0.271 10 false No. 1 Integration Relay 4.646,6.375 4.917,6.583 0.271,0.208 10 false 1J 2.51,6.375 2.823,6.635 0.313,0.26 10 false 1J 2.5,6.083 2.865,6.344 0.365,0.26 10 false 1H 0.531,6.917 1.115,7.198 0.583,0.281 10 false Battery 0.99,6.24 1.719,6.51 0.729,0.271 10 false BATT P/I 0.427,5.75 0.99,5.99 0.563,0.24 10 false GLOW 2.323,5.99 2.49,6.208 0.167,0.219 10 false 1 2.323,6.5 2.521,6.708 0.198,0.208 10 false 3 4.927,6.479 5.125,6.667 0.198,0.188 10 false 2 5.74,6.198 5.969,6.375 0.229,0.177 10 false 11 2.979,3.906 3.688,4.125 0.708,0.219 10 false EFI No. 2 5.635,6.375 6.021,6.531 0.385,0.156 10 false G148 6.042,6.406 6.573,6.708 0.531,0.302 10 false MREL 5.646,0.448 6.104,0.708 0.458,0.26 10 false C114 5.646,0.854 6.083,1.052 0.438,0.198 10 false C114 6.042,0.458 6.521,0.688 0.479,0.229 10 false GLDO 6.063,0.844 6.521,1.021 0.458,0.177 10 false GLDI 5.771,0.292 6.01,0.521 0.24,0.229 10 false 20 5.771,0.698 6.01,0.906 0.24,0.208 10 false 21 1.49,0.458 1.938,0.688 0.448,0.229 10 false C118 1.49,0.865 1.948,1.104 0.458,0.24 10 false C118 1.49,4.531 1.927,4.792 0.438,0.26 10 false C118 1.49,3.781 1.969,4.021 0.479,0.24 10 false C118 0.385,4.948 1.781,5.198 1.396,0.25 10 false Glow Plug Controller 1.5,1.25 1.938,1.479 0.438,0.229 10 false C117 1.5,1.885 1.938,2.146 0.438,0.26 10 false C117 1.573,4.365 1.74,4.552 0.167,0.188 10 false 1 1.573,3.979 1.771,4.188 0.198,0.208 10 false 1 1.573,3.604 1.781,3.823 0.208,0.219 10 false 4 1.531,4.135 1.875,4.333 0.344,0.198 10 false A73 1.5,2.521 1.948,2.792 0.448,0.271 10 false C116 1.5,3.156 1.938,3.354 0.438,0.198 10 false C116 1.573,2.354 1.729,2.521 0.156,0.167 10 false 1 1.573,2.99 1.76,3.188 0.188,0.198 10 false 2 1.573,1.083 1.76,1.302 0.188,0.219 10 false 1 1.583,1.708 1.802,1.885 0.219,0.177 10 false 2 1.573,0.292 1.802,0.5 0.229,0.208 10 false 3 1.573,0.708 1.802,0.896 0.229,0.188 10 false 5 6.26,7.146 6.656,7.365 0.396,0.219 10 false ECM 2.865,1.469 3.969,1.708 1.104,0.24 10 false No. 1 Glow Plug 2.865,2.104 3.99,2.396 1.125,0.292 10 false No. 2 Glow Plug 2.865,2.75 3.979,2.969 1.115,0.219 10 false No. 3 Glow Plug 2.865,3.406 3.958,3.646 1.094,0.24 10 false No. 4 Glow Plug 3.177,6.219 3.5,6.417 0.323,0.198 10 false EFI 1.26,0.458 1.479,0.656 0.219,0.198 10 false SI 1.26,0.865 1.49,1.104 0.229,0.24 10 false DI 1.146,1.24 1.5,1.49 0.354,0.25 10 false GL1 1.146,1.875 1.469,2.083 0.323,0.208 10 false GL2 1.146,2.521 1.469,2.729 0.323,0.208 10 false GL3 1.146,3.167 1.438,3.385 0.292,0.219 10 false GL4 1.229,3.781 1.469,3.99 0.24,0.208 10 false +B 1.073,4.146 1.469,4.365 0.396,0.219 10 false BATT 1.104,4.563 1.479,4.75 0.375,0.188 10 false GND 3.823,6.667 4.271,6.896 0.448,0.229 10 false MAIN 4.927,5.99 5.125,6.156 0.198,0.167 10 false 5 3.052,5.958 3.208,6.146 0.156,0.188 10 false 1 3.427,5.958 3.583,6.167 0.156,0.208 10 false 2 4.646,6.094 4.906,6.302 0.26,0.208 10 false 1J

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P0683 is output A
P052F is output B




A

2.CHECK GLOW PLUG CONTROLLER (POWER SOURCE CIRCUIT)

B

7.REPLACE GLOW PLUG CONTROLLER
2.CHECK GLOW PLUG CONTROLLER (POWER SOURCE CIRCUIT)
a.
A241954C03
0.542,1 1.01,1.271 0.469,0.271 1.917,1.677 1.76,1.188 true 0.125,0.146 0.438,0.344 0.313,0.198 10 false *a 0.615,1.052 0.969,1.271 0.354,0.219 10 false C118 1.885,1.667 2.198,1.865 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Glow Plug Controller)


Disconnect the glow plug controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C118-4 (+B) - Body ground Ignition switch ON 11 to 14 V
C118-4 (+B) - Body ground Ignition switch off Below 0.5 V



c.

Reconnect the glow plug controller connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)

NG

9.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)
a.

Disconnect the glow plug controller connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C118-1 (GND) - Body ground Always Below 1 Ω



c.

Reconnect the glow plug controller connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)
a.

Disconnect the glow plug controller connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C118-3 (SI) - C114-20 (GLDO) Always Below 1 Ω
C118-5 (DI) - C114-21 (GLDI) Always Below 1 Ω
C118-3 (SI) or C114-20 (GLDO) - Body ground Always 10 kΩ or higher
C118-5 (DI) or C114-21 (GLDI) - Body ground Always 10 kΩ or higher



d.

Reconnect the glow plug controller connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE GLOW PLUG CONTROLLER

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE GLOW PLUG CONTROLLER

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Using the intelligent tester, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>CHECK MODE PROCEDURE

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 61 1

g.

Confirm that the DTC is not output again.

HINT:

Check for DTCs in check mode.



Result:
Proceed to
OK
NG



OK

END

NG

11.REPLACE ECM
7.REPLACE GLOW PLUG CONTROLLER

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Using the intelligent tester, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>CHECK MODE PROCEDURE

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 61 1

g.

Confirm that the DTC is not output again.

HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END

9.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - NO. 1 INTEGRATION RELAY)
a.

Disconnect the glow plug controller connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C118-4 (+B) - 1J-5 Always Below 1 Ω
C118-4 (+B) or 1J-5 - Body ground Always 10 kΩ or higher



d.

Reconnect the glow plug controller connector.


e.

Reinstall the No. 1 integration relay.


Result:
Proceed to
OK
NG



OK

10.CHECK CHARGING SYSTEM

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.CHECK CHARGING SYSTEM
a.

Check the charging system and perform repairs as necessary.

Click herePower Source / Network>1KD-FTV BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Using the intelligent tester, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>CHECK MODE PROCEDURE

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 61 1

g.

Confirm that the DTC is not output again.

HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED