Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the ECM memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0560 System Voltage The voltage at terminal BATT drops excessively for 3 seconds and part of the stored values in the ECM are initialized (1 trip detection logic).
·

Open in backup power source circuit (to BATT terminal)

·

Battery

·

Battery terminals

·

EFI fuse

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0560 Battery Voltage*

*: This is not the voltage at terminal BATT, it is the power supply voltage for the ECM.

HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.


CONFIRMATION DRIVING PATTERN

P0560
DTC Detection Drive Pattern Ignition switch ON for 3 seconds

WIRING DIAGRAM

A276473
2.74,0.875 3.052,1.063 0.313,0.188 10 false EFI 2.688,0.583 2.844,0.781 0.156,0.198 10 false 1 2.927,0.583 3.083,0.781 0.156,0.198 10 false 2 0.76,1.146 1.76,1.417 1,0.271 10 false BATT P/I 0.865,1.875 1.427,2.125 0.563,0.25 10 false Battery 5.438,0.542 5.625,0.729 0.188,0.188 10 false 23 5.344,0.708 5.781,0.885 0.438,0.177 10 false G149 5.344,2 5.792,2.198 0.448,0.198 10 false C112 5.438,1.833 5.625,2.021 0.188,0.188 10 false 1 5.771,0.698 6.385,0.896 0.615,0.198 10 false BATT 5.771,2 6.385,2.198 0.615,0.198 10 false E1 6.156,2.521 6.521,2.719 0.365,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When the ignition switch is turned to ON, even though +B voltage is present, when the voltage at terminal BATT (power supply for maintaining memorized values in the ECM) drops excessively, this DTC is stored.



PROCEDURE

1.CHECK ECM TERMINAL VOLTAGE (BATT)
a.
A302635
0.125,0.198 0.542,0.458 0.417,0.26 0.313,1.083 0.521,1.542 true 0.156,0.25 0.51,0.438 0.354,0.188 10 false G149 0.063,0.01 0.417,0.208 0.354,0.198 10 false *a 0.417,1.583 1.156,1.813 0.74,0.229 10 true 23 (BATT)
*a Component with harness connected
(ECM)


Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G149-23 (BATT) - Body ground Always 11 to 14 V



c.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT BATTERY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY TERMINAL

NG

7.RECHARGE OR REPLACE BATTERY
3.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

8.REPAIR OR REPLACE BATTERY TERMINAL
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON for 3 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

g.

Read the DTCs.

Result:
Result Proceed to
P0560 is output A
No DTC is output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.RECHARGE OR REPLACE BATTERY
a.

Recharge or replace the battery.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE BATTERY TERMINAL
a.

Repair or replace the battery terminal.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON for 3 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END