Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.5 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
·

Starter relay circuit

·

Ignition switch

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0617 Starter Signal

CONFIRMATION DRIVING PATTERN

P0617
DTC Detection Drive Pattern Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more

WIRING DIAGRAM

A276474
1.146,4.031 1.688,4.271 0.542,0.24 10 false Battery 1.781,0.979 2.813,1.177 1.031,0.198 10 false Ignition Switch 3.583,2.354 4.229,2.552 0.646,0.198 10 false ST 5.229,1.479 5.594,1.677 0.365,0.198 10 false 6 5.073,1.656 5.479,1.938 0.406,0.281 10 false G149 5.49,1.656 5.854,1.854 0.365,0.198 10 false STA 5.875,4.5 6.24,4.667 0.365,0.167 10 false ECM 1.823,0.396 2.167,0.594 0.344,0.198 10 false AM2 2.396,0.385 2.74,0.583 0.344,0.198 10 false ST2 2.24,4.125 2.729,4.323 0.49,0.198 10 false Starter 3.438,0.958 3.688,1.156 0.25,0.198 10 false ST 1.042,2.365 1.375,2.563 0.333,0.198 10 false AM2 1.792,0.823 2.063,1 0.271,0.177 10 false G9 2.656,1.979 2.813,2.146 0.156,0.167 10 false 5 2.646,2.729 2.802,2.896 0.156,0.167 10 false 3 3.417,1.979 3.573,2.146 0.156,0.167 10 false 1 3.417,2.729 3.573,2.896 0.156,0.167 10 false 2 1.656,0.406 1.813,0.573 0.156,0.167 10 false 5 2.74,0.406 2.896,0.573 0.156,0.167 10 false 7 1.677,3.646 1.948,3.865 0.271,0.219 10 false D1 2.677,3.01 3.01,3.177 0.333,0.167 10 false C32 1.719,3.469 1.844,3.635 0.125,0.167 10 false 1 2.51,3.01 2.635,3.177 0.125,0.167 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).



HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 61 193

d.

Read the value displayed on the tester when the ignition switch is turned to ON.

OK:
Ignition Switch Positions Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

2.CONFIRM WHETHER DTC OUTPUT RECURS

NG

3.INSPECT IGNITION SWITCH
2.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.


f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

3.INSPECT IGNITION SWITCH
a.

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR

NG

6.REPLACE IGNITION SWITCH
4.CHECK HARNESS AND CONNECTOR
a.

Disconnect the ignition switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-7 (ST2) or G149-6 (STA) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the ignition switch connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER DTC OUTPUT RECURS
6.REPLACE IGNITION SWITCH
a.

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER DTC OUTPUT RECURS
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER DTC OUTPUT RECURS
8.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.


f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END