Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0627  Fuel Pump Control Circuit / Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0627 Fuel Pump Control Circuit / Open Even though the CPU (command area inside the ECU) is outputting the suction control valve operation duty, the output monitor signal is absent for 0.5 seconds (1 trip detection logic).
·

Open or short in suction control valve circuit

·

Suction control valve

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0627
·

Fuel Press

·

Target Common Rail Pressure



HINT:
·

For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

·

When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Fuel Press.

Under a stable operating condition such as idling, Fuel Press is within 5000 kPa of Target Common Rail Pressure.



CONFIRMATION DRIVING PATTERN

P0627
DTC Detection Drive Pattern Idling for 1 second

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.
A239632C04
1.188,1.385 0.656,1.781 0.656,1.781 0.552,1.781 true 0.323,1.688 0.51,1.833 0.188,0.146 10 false *2 0.177,0.073 0.396,0.219 0.219,0.146 10 false *1
*1 Fuel Supply Pump Assembly
*2 Suction Control Valve


Disconnect the suction control valve connector.


b.

Measure the resistance of the suction control valve.

OK:

No open or short circuit malfunction.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

NG

4.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
2.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C5-1 - C111-23 (PCV+) Always Below 1 Ω
C5-2 - C111-12 (PCV-) Always Below 1 Ω
C5-1 or C111-23 (PCV+) - Body ground Always 10 kΩ or higher
C5-2 or C111-12 (PCV-) - Body ground Always 10 kΩ or higher



d.

Reconnect the suction control valve connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Start the engine and idle it for 1 second or more.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

f.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
P0627 is output B




A

END

B

9.REPLACE ECM
4.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

6.PERFORM FUEL SUPPLY PUMP INITIALIZATION
6.PERFORM FUEL SUPPLY PUMP INITIALIZATION
a.

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine and idle it for 1 second or more.


e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED