Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P1626  Idle Signal Output Value Too Low  P1627  Idle Signal Output Value Too High  


DESCRIPTION

The ECM reduces injector operation speed and applied voltage to the injector to reduce the sound it produces during idling. To do this, the ECM outputs applied voltage switching signals to terminal IJEN of the injector driver from terminal IDLO of the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1626 Idle Signal Output Value Too Low With the engine running at idle, voltage of the ECM IDLO terminal is 0.05 V or less for 5 seconds or more (1 trip detection logic).
·

Open or short in idle control circuit

·

injector driver

·

ECM


Comes on DTC stored
P1627 Idle Signal Output Value Too High With the engine running at speeds higher than idle, voltage of the ECM IDLO terminal is 3.4 V or higher for 5 seconds or more (1 trip detection logic).
·

Open or short in idle control circuit

·

injector driver

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P1626, P1627
DTC Detection Drive Pattern Warm up the engine and idle it for 5 seconds

WIRING DIAGRAM

A205143
6.167,2.229 6.552,2.406 0.385,0.177 10 false C111 6.177,2.385 6.625,2.635 0.448,0.25 10 false ECM 5.844,1.125 6.323,1.375 0.479,0.25 10 false IDLO 5.573,1.021 5.833,1.25 0.26,0.229 10 false 19 1.5,1.021 1.75,1.25 0.25,0.229 10 false 2 1.073,1.135 1.438,1.354 0.365,0.219 10 false IJEN 0.625,2.458 2.281,2.708 1.656,0.25 10 false Injector Driver 0.802,2.302 1.292,2.542 0.49,0.24 10 false C109

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)
a.

Disconnect the injector driver connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C109-2 (IJEN) - C111-19 (IDLO) Always Below 1 Ω
C109-2 (IJEN) or C111-19 (IDLO) - Body ground Always 10 kΩ or higher



d.

Reconnect the injector driver connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

2.REPLACE INJECTOR DRIVER

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.REPLACE INJECTOR DRIVER
a.

Replace the injector driver.

Click hereEngine / Hybrid System>1KD-FTV FUEL>INJECTOR DRIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CHECK ANY OTHER DTCS OUTPUT
3.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
P1626 or P1627 is output B




A

END

B

4.REPLACE ECM
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

After warming up the engine, idle the engine for 5 seconds or more.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END