Refer to DTC P0545 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P0545).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2084 | Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2 | All conditions are met (2 trip detection logic):
(a) The battery voltage is 8 V or higher. (b) After the engine is stopped and the vehicle is left as is for 10 hours or more, the difference between "Exhaust Temperature B1S2" and "Coolant Temp" is 400°C (752 °F) or more when the ignition switch is turned to ON. |
·
Exhaust gas temperature sensor B1S2 ·
Engine coolant temperature sensor ·
ECM (soak timer) |
Comes on | DTC stored |
| P242B | Exhaust Gas Temperature Sensor Circuit Range / Performance Bank 1 Sensor 3 | All conditions are met (2 trip detection logic):
(a) The battery voltage is 8 V or higher. (b) After the engine is stopped and the vehicle is left as is for 10 hours or more, the difference between "Exhaust Temperature B1S3" and "Coolant Temp" is 400°C (752 °F) or more when the ignition switch is turned to ON. |
·
Exhaust gas temperature sensor B1S3 ·
Engine coolant temperature sensor ·
ECM (soak timer) |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P2084 | ·
Exhaust Temperature B1S2 ·
Exhaust Temperature B1S3 ·
Coolant temp ·
Intake Air |
| P242B |
Sensor 2 represents the sensor located upstream of the DPF catalytic converter.
Sensor 3 represents the sensor located downstream of the DPF catalytic converter.
If DTC P2084 and/or P242B is stored, the following symptoms may appear:
White smoke
| DTC Detection Drive Pattern | Stop the engine, leave the vehicle as is for 1 to 2 hours and confirm that "Exhaust Temperature B1S2" is approximately the same value as "Intake Air". |
| DTC Detection Drive Pattern | Stop the engine, leave the vehicle as is for 1 to 2 hours and confirm that "Exhaust Temperature B1S3" is approximately the same value as "Intake Air". |
The ECM compares the values from exhaust temperature sensors B1S2 and B1S3 with the engine coolant temperature when the ignition switch is turned to ON after the vehicle has been left soaking for 10 hours or more. If the difference is 400°C (752 °F) or more, a DTC indicating an exhaust gas temperature sensor malfunction is stored and the MIL is illuminated (2 trip detection logic).
Refer to DTC P0545 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P0545).
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P2084 and/or P242B is output | A |
| Except above
P2084 and/or P242B and other DTCs are output |
B |
A
B
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DIAGNOSTIC TROUBLE CODE CHART
Leave the vehicle as is for 1 to 2 hours with the engine stopped.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S2 and Exhaust Temperature B1S3.
| Tester Display |
|---|
| Exhaust Temperature B1S2 |
| Exhaust Temperature B1S3 |
Read the values.
| Result | Proceed to |
|---|---|
| Value of "Exhaust Temperature B1S2" is 400°C (752°F) or higher | A |
| Value of "Exhaust Temperature B1S3" is 400°C (752°F) or higher | B |
| Except above | C |
If the exhaust gas temperature sensor is normal, the exhaust gas temperature drops when the vehicle is left as is for 1 to 2 hours with the engine stopped. If the exhaust gas temperature does not drop, the exhaust gas temperature sensor may be malfunctioning.
A
B
C
Replace the exhaust gas temperature sensor B1S2.
Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the exhaust gas temperature sensor B1S3.
Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Leave the vehicle as is for 1 to 2 hours with the engine stopped.
It is not necessary to allow the engine to soak if the engine is cold.
The engine cools faster if the hood is opened.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S2, Exhaust Temperature B1S3 and Intake Air.
| Tester Display |
|---|
| Intake Air |
| Exhaust Temperature B1S2 |
| Exhaust Temperature B1S3 |
Read the value.
The values of "Exhaust Temperature B1S2" and "Exhaust Temperature B1S3" are both approximately the same as "Intake Air".
| Proceed to |
|---|
| NEXT |
NEXT
Allow the engine to soak for 1 to 2 hours.
It is not necessary to allow the engine to soak if the engine is cold.
The engine cools faster if the hood is opened.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant temp.
| Tester Display |
|---|
| Coolant Temp |
Read the value.
The difference between the displayed value and outside air temperature is below 5°C (9°F).
If the difference between "Coolant Temp" and the outside air temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the engine coolant temperature sensor.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the engine coolant temperature sensor.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT