Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P2564  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low  P2565  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High  


DESCRIPTION

The variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.

The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the ECM. The ECM determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.

A221597
4.156,1.49 4.156,0.646 4.156,0.646 4.448,0.646 false 1.354,3.052 1.479,3.292 true 1.063,2.292 0.667,1.292 0.667,1.292 0.823,1.292 true 1.365,1.75 1.448,1.354 1.448,1.354 1.573,1.354 true 0.542,3.948 2.354,4.396 1.813,0.448 10 false Nozzle Vane Position Sensor (Turbocharger Sub-assembly) 0.875,1.188 1.365,1.438 0.49,0.25 10 false Hall IC 2.323,2.458 2.719,2.635 0.396,0.177 10 false VTA1 3,3.156 3.396,3.333 0.396,0.177 10 false VNE2 3.01,1.583 3.469,1.76 0.458,0.177 10 false VNVC 3.094,3.531 3.479,3.75 0.385,0.219 10 false ECM 4.677,3.594 5.24,3.875 0.563,0.281 10 false Closed 5.75,3.594 6.385,3.896 0.635,0.302 10 false Opened 1.625,1.26 2.177,1.5 0.552,0.24 10 false Magnet 4.49,0.583 6.115,1.073 1.625,0.49 10 false Nozzle Vane Position Sensor Output Voltage (V) 0.063,2.688 0.521,3.188 0.458,0.5 10 false Sensor Vane 4.104,1.625 4.365,1.802 0.26,0.177 10 false 4.5 4.094,2.521 4.365,2.698 0.271,0.177 10 false 0.5 1.458,3.313 2,3.583 0.542,0.271 10 false Magnet 4.792,3.25 6.198,3.469 1.406,0.219 10 true Nozzle Vane Position 2.323,1.667 2.781,1.844 0.458,0.177 10 false VNVC 3,2.385 3.396,2.563 0.396,0.177 10 false VNA 2.323,3.25 2.719,3.427 0.396,0.177 10 false VNE2

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2564 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low VNA voltage is 0.1 V or less for 2.1 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

ECM


Comes on DTC stored
P2565 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High VNA voltage is 4.9 V or higher for 2.1 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

ECM


Comes on DTC stored

HINT:

If DTC P2564 and/or P2565 is stored due to the nozzle vane being stuck open, the following symptoms may appear:

- Lack of power

- Vehicle surge or hesitation under light or medium load



CONFIRMATION DRIVING PATTERN

P2564, P2565
DTC Detection Drive Pattern Ignition switch ON for 1 second

WIRING DIAGRAM

A221590
0.74,2.875 2.688,3.229 1.948,0.354 10 false Nozzle Vane Position Sensor 0.74,2.698 1.073,2.896 0.333,0.198 10 false C40 5.438,2.708 5.875,2.917 0.438,0.208 10 false C114 5.438,2.885 5.896,3.115 0.458,0.229 10 false ECM 5.469,0.927 5.896,1.167 0.427,0.24 10 false VNVC 5.469,1.417 5.906,1.635 0.438,0.219 10 false VNA 5.469,1.865 5.958,2.104 0.49,0.24 10 false VNE2 5.229,0.917 5.448,1.125 0.219,0.208 10 false 11 5.26,1.406 5.417,1.615 0.156,0.208 10 false 6 5.208,1.865 5.458,2.073 0.25,0.208 10 false 10 1.677,1 2.135,1.281 0.458,0.281 10 false VNVC 1.729,1.5 2.156,1.76 0.427,0.26 10 false VTA1 1.688,1.948 2.135,2.177 0.448,0.229 10 false VNE2 2.198,0.917 2.396,1.177 0.198,0.26 10 false 3 2.198,1.396 2.406,1.625 0.208,0.229 10 false 1 2.198,1.865 2.396,2.042 0.198,0.177 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2564 AND P2565)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P2564 and/or P2565 is output A
P2564 and/or P2565 and other DTCs are output B




A

2.CHECK HARNESS AND CONNECTOR (ECM - NOZZLE VANE POSITION SENSOR)

B

2.CHECK HARNESS AND CONNECTOR (ECM - NOZZLE VANE POSITION SENSOR)
a.

Disconnect the nozzle vane position sensor connector.


b.

Disconnect the ECM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C40-1 (VTA1) - C114-6 (VNA) Always Below 1 Ω
C40-2 (VNE2) - C114-10 (VNE2) Always Below 1 Ω
C40-3 (VNVC) - C114-11 (VNVC) Always Below 1 Ω
C40-1 (VTA1) or C114-6 (VNA) - Body ground Always 10 kΩ or higher
C40-3 (VNVC) or C114-11 (VNVC) - Body ground Always 10 kΩ or higher



d.

Reconnect the nozzle vane position sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (VNVC VOLTAGE)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.INSPECT ECM (VNVC VOLTAGE)
a.
A302635
1.823,0.208 2.25,0.479 0.427,0.271 1.573,1.615 1.927,0.781 true 2.542,1.646 1.99,0.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.885,0.271 2.26,0.51 0.375,0.24 10 false C114 1.302,1.677 2.063,1.917 0.76,0.24 10 false 11 (VNVC) 2.302,1.667 3.063,1.906 0.76,0.24 10 false 10 (VNE2)
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C114-11 (VNVC) - C114-10 (VNE2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)

NG

7.REPLACE ECM
4.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off.


d.

Turn the ignition switch off and leave the vehicle for 15 seconds.


e.

Turn the ignition switch to ON for 1 second.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P2564 and/or P2565.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, idle the engine.



Result:
Proceed to
NEXT



NEXT

END

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED