Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2012.01–2012.04
RM1840EF _56 Audio / Visual / Telematics _009631 AUDIO / VIDEO _0052657 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B15C3  Speaker Output Short  


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C3 Speaker Output Short A short is detected in the speaker output circuit.
·

Speakers

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

C240170
5.677,6.563 6.875,6.99 1.198,0.427 10 false Radio and Display Receiver Assembly 5.875,3.073 6.156,3.24 0.281,0.167 10 false FL- 5.875,2.583 6.156,2.75 0.281,0.167 10 false FL+ 5.875,1.688 6.177,1.854 0.302,0.167 10 false FR- 5.875,1.167 6.177,1.333 0.302,0.167 10 false FR+ 5.438,5.865 5.833,6.031 0.396,0.167 10 false G128 5.438,5.354 5.833,5.521 0.396,0.167 10 false G128 5.438,4.479 5.833,4.646 0.396,0.167 10 false G128 5.438,3.958 5.833,4.125 0.396,0.167 10 false G128 5.438,3.083 5.833,3.25 0.396,0.167 10 false G129 5.438,2.573 5.833,2.74 0.396,0.167 10 false G129 5.438,1.688 5.833,1.854 0.396,0.167 10 false G129 5.438,1.167 5.833,1.333 0.396,0.167 10 false G129 2.948,1.99 5.438,2.333 2.49,0.344 10 false Front No. 2 Speaker Assembly RH 2.948,3.427 5.24,3.719 2.292,0.292 10 false Front No. 2 Speaker Assembly LH 0.729,1.24 1.979,1.729 1.25,0.49 10 false Front No. 1 Speaker Assembly RH 0.729,2.656 1.99,3.063 1.26,0.406 10 false Front No. 1 Speaker Assembly LH 5.552,0.948 5.677,1.115 0.125,0.167 10 false 1 5.563,1.469 5.688,1.635 0.125,0.167 10 false 5 5.573,2.344 5.698,2.51 0.125,0.167 10 false 2 5.563,2.865 5.688,3.031 0.125,0.167 10 false 6 4.344,1.063 4.469,1.229 0.125,0.167 10 false 4 4.344,1.573 4.469,1.74 0.125,0.167 10 false 2 3.885,1.083 4.396,1.302 0.51,0.219 10 false TWR+ 3.927,1.792 4.385,2 0.458,0.208 10 false TWR- 3.51,1.073 3.635,1.24 0.125,0.167 10 false 3 3.51,1.573 3.635,1.74 0.125,0.167 10 false 1 3.698,1.073 3.823,1.24 0.125,0.167 10 false + 3.698,1.792 3.854,2.01 0.156,0.219 10 false - 3.896,2.479 4.365,2.646 0.469,0.167 10 false TWL+ 3.927,3.188 4.365,3.354 0.438,0.167 10 false TWL- 3.688,2.479 3.813,2.646 0.125,0.167 10 false + 3.688,3.156 3.813,3.323 0.125,0.167 10 false - 4.344,2.479 4.469,2.646 0.125,0.167 10 false 4 4.344,2.979 4.469,3.146 0.125,0.167 10 false 2 3.51,2.479 3.635,2.646 0.125,0.167 10 false 3 3.51,2.99 3.635,3.156 0.125,0.167 10 false 1 2.323,1.573 2.448,1.74 0.125,0.167 10 false 2 2.313,1.271 2.438,1.438 0.125,0.167 10 false 1 2.323,2.979 2.448,3.146 0.125,0.167 10 false 2 2.313,2.688 2.438,2.854 0.125,0.167 10 false 1 5.875,5.865 6.156,6.031 0.281,0.167 10 false RL- 5.875,5.354 6.156,5.521 0.281,0.167 10 false RL+ 5.875,4.469 6.177,4.635 0.302,0.167 10 false RR- 5.875,3.958 6.177,4.125 0.302,0.167 10 false RR+ 5.563,3.74 5.688,3.906 0.125,0.167 10 false 1 5.573,4.26 5.698,4.427 0.125,0.167 10 false 3 5.573,5.135 5.698,5.302 0.125,0.167 10 false 2 5.573,5.646 5.698,5.813 0.125,0.167 10 false 6 0.719,4.042 1.594,4.49 0.875,0.448 10 false Rear Speaker Assembly RH 0.719,5.448 1.583,5.896 0.865,0.448 10 false Rear Speaker Assembly LH 2.323,5.469 2.448,5.635 0.125,0.167 10 false 1 2.333,5.76 2.458,5.927 0.125,0.167 10 false 2 2.313,4.073 2.438,4.24 0.125,0.167 10 false 1 2.323,4.385 2.448,4.552 0.125,0.167 10 false 2 2.948,1.844 3.26,2.01 0.313,0.167 10 false H6 2.948,3.25 3.26,3.417 0.313,0.167 10 false I6 0.729,1.073 1.042,1.24 0.313,0.167 10 false H4 0.729,2.479 1.042,2.646 0.313,0.167 10 false I1 0.729,3.854 1.042,4.021 0.313,0.167 10 false J7 0.729,5.281 1.042,5.448 0.313,0.167 10 false J3

PROCEDURE

1.CHECK FOR DTC
a.

Disconnect the G129 and G128 radio and display receiver assembly connectors.



c.

Check if DTC B15C3 is output.

OK:

DTC B15C3 is not output.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTC

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK FOR DTC
a.

Reconnect the G128 radio and display receiver assembly connector.



c.

Check if DTC B15C3 is output.

OK:

DTC B15C3 is not output.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - FRONT NO. 2 SPEAKER)

NG

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - REAR SPEAKER)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - FRONT NO. 2 SPEAKER)
a.

Disconnect the G129 radio and display receiver assembly connector.


b.

Disconnect the H6*1 and/or I6*2 front No. 2 speaker connector.

*1: for RH

*2: for LH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
G129-1 (FR+) - H6-4 (TWR+) Always Below 1 Ω
G129-5 (FR-) - H6-2 (TWR-)
G129-1 (FR+) - Body ground Always 10 kΩ or higher
G129-5 (FR-) - Body ground

for LH
Tester Connection Condition Specified Condition
G129-2 (FL+) - I6-4 (TWL+) Always Below 1 Ω
G129-6 (FL-) - I6-2 (TWL-)
G129-2 (FL+) - Body ground Always 10 kΩ or higher
G129-6 (FL-) - Body ground



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 1 SPEAKER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 1 SPEAKER)

*1: for RH

*2: for LH


a.

Disconnect the H6*1 and/or I6*2 front No. 2 speaker connector.


b.

Disconnect the H4*1 and/or I1*2 front No. 1 speaker connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
H6-3 (+) - H4-1 Always Below 1 Ω
H6-1 (-) - H4-2
H6-3 (+) - Body ground Always 10 kΩ or higher
H6-1 (-) - Body ground

for LH
Tester Connection Condition Specified Condition
I6-3 (+) - I1-1 Always Below 1 Ω
I6-1 (-) - I1-2
I6-3 (+) - Body ground Always 10 kΩ or higher
I6-1 (-) - Body ground



Result:
Proceed to
OK
NG



OK

5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.
E178457

Disconnect the H4*1 and/or I1*2 front No. 1 speaker connector.

*1: for RH

*2: for LH



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 4 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

6.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Temporarily replace the front No. 2 speaker with a new or normally functioning one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.

Check that the malfunction disappears.

HINT:
·

Connect all the speaker connectors to the speakers.

·

When there is a possibility that either the right or left speaker is defective, inspect by interchanging the right one with the left one.



Result:
Result Proceed to
Malfunction disappears A
Malfunction does not disappear B




A

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - REAR SPEAKER)
a.

Disconnect the G128 radio and display receiver assembly connector.


b.

Disconnect the J7*1 and/or J3*2 rear speaker connector.

*1: for RH

*2: for LH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
G128-1 (RR+) - J7-1 Always Below 1 Ω
G128-3 (RR-) - J7-2
G128-1 (RR+) - Body ground Always 10 kΩ or higher
G128-3 (RR-) - Body ground

for LH
Tester Connection Condition Specified Condition
G128-2 (RL+) - J3-1 Always Below 1 Ω
G128-6 (RL-) - J3-2
G128-2 (RL+) - Body ground Always 10 kΩ or higher
G128-6 (RL-) - Body ground



Result:
Proceed to
OK
NG



OK

8.INSPECT REAR SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR SPEAKER ASSEMBLY
a.
E178457

Disconnect the J7*1 and/or J3*2 rear speaker connector.

*1: for RH

*2: for LH



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 4 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG