These DTCs indicate that the DC motor of the turbocharger is malfunctioning. The ECM monitors the DC motor current to detect an open or short in the DC motor circuit. If the current meets certain criteria, the ECM stores a DTC and illuminates the MIL immediately.
The DC motor is used to operate the nozzle vane of the turbocharger. The nozzle vane opens and closes to change the velocity of exhaust emissions in order to control the turbo pressure. The ECM varies the duty ratio of the DC motor in accordance with the driving conditions.
If the nozzle vane is stuck closed (DC motor stuck off), drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (DC motor stuck on), drivability may deteriorate at intermediate throttle positions or the engine power may be insufficient.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0046 | Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance | Either condition is met when the motor is operating (1 trip detection logic):
·
The DC motor duty ratio exceeds the threshold for 0.5 seconds for the specified number of times (in terms of time, this amounts to 100 seconds or more). ·
DC motor current is 2.2 A or higher for 5 seconds or more. |
·
Open or short in DC motor (turbocharger sub-assembly) circuit ·
DC motor (turbocharger sub-assembly) ·
Turbocharger nozzle vane is stuck or movement is irregular |
Comes on | DTC stored |
| P0047 | Turbocharger/Supercharger Boost Control "A" Circuit Low | The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more (1 trip detection logic). | ·
Open in DC motor (turbocharger sub-assembly) circuit ·
DC motor (turbocharger sub-assembly) ·
Turbocharger nozzle vane is stuck or movement is irregular |
Comes on | DTC stored |
| P0048 | Turbocharger/Supercharger Boost Control "A" Circuit High | Overcurrent is detected 25 times or more (0.4 seconds or more) (1 trip detection logic). | ·
Short in DC motor (turbocharger sub-assembly) circuit ·
DC motor (turbocharger sub-assembly) ·
Turbocharger nozzle vane is stuck or movement is irregular |
Comes on | DTC stored |
If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck closed, the following symptom may appear:
Vehicle surge when driving with full load
If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck open, the following symptoms may appear:
Lack of power
Vehicle surge or hesitation under light or medium load
| DTC Detection Drive Pattern | Ignition switch ON for 5 seconds |
| DTC Detection Drive Pattern | 2 seconds after engine is started, race enginefor 1 second |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0046, P0047 and/or P0048 is output | A |
| P0046, P0047 and/or P0048 and other DTCs are output | B |
If codes other than P0046, P0047 and/or P0048 are output, perform troubleshooting for those DTCs first.
A
B
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DIAGNOSTIC TROUBLE CODE CHART
Inspect the turbocharger sub-assembly.
Click hereEngine / Hybrid System>2KD-FTV INTAKE / EXHAUST>INTAKE SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(DC Motor) |
Disconnect the DC motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 (M-) - 2 (M+) | Always | 1 to 100 Ω |
Reconnect the DC motor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the DC motor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C41-1 (M-) - C112-14 (M-) | Always | Below 1 Ω |
| C41-2 (M+) - C112-15 (M+) | Always | Below 1 Ω |
| C41-1 (M-) or C112-14 (M-) - Body ground | Always | 10 kΩ or higher |
| C41-2 (M+) or C112-15 (M+) - Body ground | Always | 10 kΩ or higher |
Reconnect the DC motor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON for 5 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the turbocharger sub-assembly.
Click hereEngine / Hybrid System>2KD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/ TURBOCHARGER(for DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT