Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052068 ECD SYSTEM(for DPF) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0101  Mass or Volume Air Flow Circuit Range / Performance Problem  


DESCRIPTION

Refer to DTC P0100 (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P0100).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0101 Mass or Volume Air Flow Circuit Range / Performance Problem After the engine is completely warmed up, while the accelerator pedal is released for 7 seconds or more and the vehicle is decelerating, the intake air volume is higher or lower than the threshold* (EGR valve fully closed and throttle valve is fully open).
(2 trip detection logic)
·

Mass air flow meter

·

Intake air temperature sensor (turbo)

·

Manifold absolute pressure sensor

·

Electric EGR control valve assembly

·

ECM

·

Open or short in mass air flow meter circuit


Comes on DTC stored

*: There is a threshold for a low air flow rate malfunction and high air flow rate malfunction. The threshold is different depending on the values of "Engine Speed", "MAP" and "Intake Air Temp (Turbo)".

HINT:
·

Low air flow rate malfunction: For example when vehicle deceleration if "MAF" is 20 gm/s or less, low air flow malfunction is confirmed (at "Engine Speed" is 1600 rpm, "MAP" is 110 kPa and "Intake Air Temp (Turbo)" is 35°C).

·

High air flow rate malfunction: For example when vehicle deceleration if "MAF" is 42 gm/s or more, high air flow malfunction is confirmed (at "Engine Speed" is 1600 rpm, "MAP" is 110 kPa and "Intake Air Temp (Turbo)" is 35°C).



Related Data List
DTC No. Data List
P0101
·

MAF

·

MAP

·

Engine Speed

·

Intake Air Temp (Turbo)

·

Target EGR Position

·

Actual EGR Valve Pos.

·

EGR Close Lrn. Status

·

Exhaust Temperature B1S2



HINT:

If DTC P0101 is stored, either of the following symptoms may appear:

1.

As the ECU mistakenly determines that there is less air than the actual intake air amount, EGR is decreased to match the target EGR.

·

Combustion noise worsens


2.

As the ECU mistakenly determines that there is more air than the actual intake air amount, EGR is increased to match the target EGR:

·

Misfire

·

White smoke

·

Black smoke




CONFIRMATION DRIVING PATTERN

P0101
DTC Detection Drive Pattern After the engine is completely warmed up, perform the following procedure 3 times: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
After performing the above procedure, immediately stop the vehicle and confirm that "Exhaust Temperature B1S2" displays 300°C (572°F) or higher using the intelligent tester.

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0101)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P0101 and other DTCs are output A
P0101 is output B


HINT:

If codes other than P0101 are output, perform troubleshooting for those DTCs first.




A

B

2.CHECK FREEZE FRAME DATA (MASS AIR FLOW RATE AND ENGINE SPEED)
2.CHECK FREEZE FRAME DATA (MASS AIR FLOW RATE AND ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Check the freeze frame data.

Result:
Result Proceed to
·

Engine speed 1350 rpm or less

·

MAF 246.0 gm/s or more


A
·

Engine speed 1350 rpm or more

·

MAF 0.03 gm/s or less


Except above B




A

3.READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE AND ENGINE SPEED)

B

8.READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE AND ENGINE SPEED)
3.READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE AND ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Engine speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
MAF
50003 61 315,319

d.

Read the value.

Standard:
Engine speed MAF
0 rpm 0.5 gm/s or less
700 to 800 rpm 100 gm/s or less
3000 rpm 1 gm/s or more



Result:
Proceed to
OK
NG



OK

4.REPLACE MASS AIR FLOW METER

NG

13.REPLACE HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
4.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>MASS AIR FLOW METER(w/ DPF)>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.


f.

Stop the vehicle immediately after completing the above procedure.


g.

Connect the intelligent tester to the DLC3.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S2.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
50003 61 1062
HINT:
·

"Exhaust Temperature B1S2" must be 300°C or more.

·

If "Exhaust Temperature B1S2" is less than 300°C (572°F), perform the DTC detection drive pattern again, increasing the vehicle speed so that the exhaust gas temperature increases.




i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

j.

Read the pending DTCs.

HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0101.


iii.

Check the DTC judgment result.

Result:
Tester Display Result Proceed to
All Readiness NORMAL A
ABNORMAL B
Pending DTC P0101 is output


HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.





A

END

B

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C115-5 (FG) - C113-17 (VG) Always Below 1 Ω
C115-4 (E2G) - C113-18 (EVG) Always Below 1 Ω
C115-5 (FG) or C113-17 (VG) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

24.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE AND ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Engine speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
MAF
50003 61 315,319

d.

Read the value.

Standard:
Engine speed MAF
0 rpm 0.35 gm/s or less



Result:
Proceed to
OK
NG



OK

9.READ VALUE USING INTELLIGENT TESTER (MAP AND ATMOSPHERIC PRESSURE)

NG

13.REPLACE HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
9.READ VALUE USING INTELLIGENT TESTER (MAP AND ATMOSPHERIC PRESSURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmospheric Pressure.

Powertrain > Engine > Data List
Tester Display
Atmosphere Pressure
MAP
50003 61 64,314

d.

Compare the values when the ignition switch is ON.

Standard:

Difference between "MAP" and "Atmosphere Pressure" is less than 8 kPa.


HINT:
·

If "MAP" and "Atmosphere Pressure" have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.

·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather.




Result:
Proceed to
OK
NG



OK

10.CHECK AIR INDUCTION SYSTEM

NG

26.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
10.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage.

Click hereEngine / Hybrid System>2KD-FTV INTAKE / EXHAUST>INTAKE SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION

OK:

No leakage from air induction system.


HINT:
·

Check for abnormal disconnection, pipe and hose squashing, and any damage in the intake system.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

Air leaks from the intake system can be checked by applying soapy water and revving the engine.

·

Check for any modifications in the intake system made by the user.




Result:
Proceed to
OK
NG



OK

11.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR AND INTAKE AIR TEMP [TURBO])

NG

20.REPAIR OR REPLACE AIR INDUCTION SYSTEM
11.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR AND INTAKE AIR TEMP [TURBO])
a.

Connect the intelligent tester to the DLC3.


b.

Soak the engine for a long time.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air, Intake Air Temp (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air
Intake Air Temp (Turbo)
50003 61 318,240
OK:

Intake Air is the same as Intake Air Temp (Turbo).



Result:
Proceed to
OK
NG



OK

12.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY

NG

16.INSPECT INTAKE AIR TEMPERATURE SENSOR (TURBO)
12.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.

Powertrain > Engine > Active Test
Tester Display
Control the EGR Step Position
50004 61 95

d.

When changing the Active Test continuously value to 0, 30, 60, 90, 60, 30 and 0%, check that Actual EGR Valve Pos. smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



e.

Enter the following menus: Powertrain / Engine and ECT / Data List / EGR Close Lrn. Status.

Powertrain > Engine > Data List
Tester Display
EGR Close Lrn. Status
50003 61 427

f.

Read the values.

Standard:

EGR Close Lrn. Status is OK



Result:
Proceed to
OK
NG



OK

13.REPLACE HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

17.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
13.REPLACE HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C115-5 (FG) - C113-17 (VG) Always Below 1 Ω
C115-4 (E2G) - C113-18 (EVG) Always Below 1 Ω
C115-5 (FG) or C113-17 (VG) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

14.REPLACE MASS AIR FLOW METER

NG

24.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>MASS AIR FLOW METER(w/ DPF)>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
15.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.


f.

Stop the vehicle immediately after completing the above procedure.


g.

Connect the intelligent tester to the DLC3.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S2.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
50003 61 1062
HINT:
·

"Exhaust Temperature B1S2" must be 300°C or more.

·

If "Exhaust Temperature B1S2" is less than 300°C (572°F), perform the DTC detection drive pattern again, increasing the vehicle speed so that the exhaust gas temperature increases.




i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

j.

Read the pending DTCs.

HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0101.


iii.

Check the DTC judgment result.

Result:
Tester Display Result Proceed to
All Readiness NORMAL A
ABNORMAL B
Pending DTC P0101 is output


HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.





A

END

B

23.REPLACE ECM
16.INSPECT INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Inspect the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR(w/ DPF)>INSPECTION


Result:
Proceed to
OK
NG



OK

18.REPLACE MASS AIR FLOW METER

NG

21.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
17.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY

Result:
Proceed to
OK
NG


b.

Visually check the electric EGR control valve for deposits. If there are deposits, clean the electric EGR control valve.

NOTICE:
·

When cleaning the electric EGR control valve, make sure the valve is completely closed.

·

Do not forcibly open the valve, as it may be damaged or deformed.

·

When cleaning the electric EGR control valve, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.




c.
A233146
0.656,2.625 0.875,2.844 0.219,0.219 3.063,2.458 2.875,2.458 2.875,2.458 2.698,3.219 true 2.146,4.375 2.333,4.375 2.333,4.375 2.708,3.865 true 0.76,3.302 0.76,2.854 false 0.719,2.656 0.844,2.802 0.125,0.146 10 false A 3.115,2.354 3.271,2.531 0.156,0.177 10 false *1 1.958,4.292 2.115,4.469 0.156,0.177 10 false *1 0.99,4.156 1.146,4.333 0.156,0.177 10 false *a 2.688,4.198 2.844,4.375 0.156,0.177 10 false *b
*1 Gap
*a OK
*b NG


Hold the electric EGR control valve up to a light, and then from the side indicated by the arrow in the illustration, visually check that there is no gap between the valve and body.

OK:

No light passes through (there is no gap between the valve and body).


If light passes through (there is a gap between the valve and body), replace the electric EGR control valve assembly.

HINT:

Light passes through part A shown in the illustration even if the valve is completely closed, this is not a problem.




OK

18.REPLACE MASS AIR FLOW METER

NG

22.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
18.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>MASS AIR FLOW METER(w/ DPF)>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
19.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.


f.

Stop the vehicle immediately after completing the above procedure.


g.

Connect the intelligent tester to the DLC3.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S2.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
50003 61 1062
HINT:
·

"Exhaust Temperature B1S2" must be 300°C or more.

·

If "Exhaust Temperature B1S2" is less than 300°C (572°F), perform the DTC detection drive pattern again, increasing the vehicle speed so that the exhaust gas temperature increases.




i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

j.

Read the pending DTCs.

HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0101.


iii.

Check the DTC judgment result.

Result:
Tester Display Result Proceed to
All Readiness NORMAL A
ABNORMAL B
Pending DTC P0101 is output


HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.





B

23.REPLACE ECM
20.REPAIR OR REPLACE AIR INDUCTION SYSTEM
a.

Repair or replace the air induction system.


Result:
Proceed to
NEXT



NEXT

25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
21.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR(w/ DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
22.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>2KD-FTV EMISSION CONTROL>EGR VALVE(w/ DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
23.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
24.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.


f.

Stop the vehicle immediately after completing the above procedure.


g.

Connect the intelligent tester to the DLC3.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S2.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
50003 61 1062
HINT:
·

"Exhaust Temperature B1S2" must be 300°C (572°F) or more.

·

If "Exhaust Temperature B1S2" is less than 300°C (572°F), perform the DTC detection drive pattern again, increasing the vehicle speed so that the exhaust gas temperature increases.




i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

j.

Confirm that the pending DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0101.


iii.

Check the DTC judgment result.

HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.




Result:
Proceed to
NEXT



NEXT

END

26.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor.


Result:
Proceed to
NEXT



NEXT

25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED