Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052068 ECD SYSTEM(for DPF) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0545  Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 1)  P0546  Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 1)  P2032  Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2)  P2033  Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 2)  P242C  Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 3  P242D  Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 3  


DESCRIPTION

A243953
5.75,4.677 5.948,4.677 false 1.76,5.427 1.875,5.427 false 1.531,2.604 1.094,2.99 false 1.531,1.698 1.198,1.063 1.198,1.063 1.104,1.063 false 2.24,1.344 2.854,0.302 2.854,0.302 4,0.302 false 2.417,2.865 3.844,3.365 3.844,3.365 4.042,3.365 false 2.448,2.042 4.479,2.208 4.479,2.208 4.594,2.208 false 4.146,0.219 6.229,0.76 2.083,0.542 10 false Exhaust Gas Temperature Sensor (B1S1) 1.521,0.552 2.365,0.823 0.844,0.271 10 false Exhaust Gas 3.167,0.969 3.531,1.24 0.365,0.271 10 false ECM 0.198,2.906 1.063,3.333 0.865,0.427 10 false DPF Catalytic Converter 4.635,2.125 7.083,2.594 2.448,0.469 10 false No. 2 Exhaust Gas Temperature Sensor (B1S2) 0.24,3.823 1.99,4.083 1.75,0.26 10 false Property of Output Voltage: 1.635,4.156 3.302,4.354 1.667,0.198 10 false Exhaust Gas Temperature 3.417,4.156 3.906,4.396 0.49,0.24 10 false °C (°F) 0.781,4.156 1.583,4.365 0.802,0.208 10 false 1000 (1832) 0.896,4.365 1.604,4.583 0.708,0.219 10 false 960 (1760) 0.896,4.656 1.583,4.896 0.688,0.24 10 false 760 (1400) 0.896,4.885 1.604,5.125 0.708,0.24 10 false 560 (1040) 0.958,5.115 1.583,5.354 0.625,0.24 10 false 360 (680) 0.958,5.354 1.573,5.573 0.615,0.219 10 false 160 (320) 1.01,5.583 1.583,5.823 0.573,0.24 10 false -40 (-40) 1.552,5.708 1.656,5.896 0.104,0.188 10 false 0 1.719,5.708 1.938,5.896 0.219,0.188 10 false 0.2 2,5.708 2.24,5.896 0.24,0.188 10 false 0.5 2.396,5.708 2.635,5.896 0.24,0.188 10 false 1.0 2.844,5.708 3.083,5.896 0.24,0.188 10 false 1.5 3.271,5.708 3.51,5.896 0.24,0.188 10 false 2.0 3.719,5.708 3.958,5.896 0.24,0.188 10 false 2.5 4.167,5.708 4.406,5.896 0.24,0.188 10 false 3.0 4.615,5.708 4.823,5.896 0.208,0.188 10 false 3.5 5.031,5.698 5.24,5.885 0.208,0.188 10 false 4.0 5.458,5.698 5.677,5.885 0.219,0.188 10 false 4.5 5.708,5.698 6.021,5.885 0.313,0.188 10 false 4.95 6.021,5.698 6.25,5.885 0.229,0.188 10 false 5.0 2.635,6.104 5.5,6.417 2.865,0.313 10 false Exhaust Gas Temperature Sensor Voltage (V) 1.917,5.365 3.875,5.625 1.958,0.26 10 false Stores P0545, P2032 or P242C 3.74,4.604 5.698,4.938 1.958,0.333 10 false Stores P0546, P2033 or P242D 4.115,3.271 6.563,3.719 2.448,0.448 10 false No. 3 Exhaust Gas Temperature Sensor (B1S3) 0.188,0.979 1.042,1.458 0.854,0.479 10 false CCo Catalytic Converter

The exhaust gas temperature sensors are installed before and after the DPF catalytic converter to sense the exhaust gas temperature.

A thermistor built into the sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature, the higher the thermistor resistance value. The higher the exhaust gas temperature, the lower the thermistor resistance value.

The exhaust gas temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the exhaust gas temperature sensor from terminal THCF (B1S1), THCI (B1S2) and THCO (B1S3) via resistor R.

Resistor R and the exhaust gas temperature sensor are connected in series. When the resistance value of the exhaust gas temperature sensor changes in accordance with the exhaust gas temperature, the voltage at terminals THCF (B1S1), THCI (B1S2) and THCO (B1S3) also changes. The No. 1 exhaust gas temperature sensor monitors the temperature upstream of the CCo catalyst. The No. 2 exhaust gas temperature sensor monitors the temperature upstream of the DPF catalyst. The No. 3 exhaust gas temperature sensor monitors the rise in temperature of the DPF catalyst. When PM forced regeneration is needed, the ECM operates the exhaust fuel addition injector to obtain target upstream temperature of the DPF catalytic converter as monitored through sensor 2. In addition, the ECM monitors the temperature increase of the DPF catalytic converter using sensor 3.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0545 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 1) Exhaust gas temperature sensor (B1S1) output voltage is below 0.2 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or more


·

Open or short in exhaust gas temperature sensor (B1S1) circuit

·

Exhaust gas temperature sensor (B1S1)

·

ECM


Comes on DTC stored
P0546 Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 1) Exhaust gas temperature sensor (B1S1) output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or more


·

Open or short in exhaust gas temperature sensor (B1S1) circuit

·

Exhaust gas temperature sensor (B1S1)

·

ECM


Comes on DTC stored
P2032 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2) No. 2 exhaust gas temperature sensor (B1S2) output voltage is below 0.2 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or more


·

Open or short in No. 2 exhaust gas temperature sensor (B1S2) circuit

·

No. 2 exhaust gas temperature sensor (B1S2)

·

ECM


Comes on DTC stored
P2033 Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 2) No. 2 exhaust gas temperature sensor (B1S2) output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or more


·

Open or short in No. 2 exhaust gas temperature sensor (B1S2) circuit

·

No. 2 exhaust gas temperature sensor (B1S2)

·

ECM


Comes on DTC stored
P242C Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 3 No. 3 exhaust gas temperature sensor (B1S3) output voltage is below 0.2 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or more


·

Open or short in No. 3 exhaust gas temperature sensor (B1S3) circuit

·

No. 3 exhaust gas temperature sensor (B1S3)

·

ECM


Comes on DTC stored
P242D Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 3 No. 3 exhaust gas temperature sensor (B1S3) output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or more


·

Open or short in No. 3 exhaust gas temperature sensor (B1S3) circuit

·

No. 3 exhaust gas temperature sensor (B1S3)

·

Abnormal rise in temperature due to melting of DPF catalytic converter

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0545 Exhaust Temperature B1S1
P0546
P2032 Exhaust Temperature B1S2
P2033
P242C Exhaust Temperature B1S3
P242D

HINT:
·

DTC P20CF (Exhaust fuel addition injector malfunction) may be stored if there is an open malfunction in an exhaust gas temperature sensor circuit.

·

Sensor 1 represents the sensor located upstream of the CCo catalytic converter.

·

Sensor 2 represents the sensor located upstream of the DPF catalytic converter.

·

Sensor 3 represents the sensor located downstream of the DPF catalytic converter.

·

When DTC P0545, P0546, P2032, P2033, P242C and/or P242D is output, check the upstream and downstream exhaust gas temperature indicated by "Powertrain / Engine and ECT / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3" using the intelligent tester.


Reference:
Condition Exhaust Gas Temperature Exhaust Gas Temperature Sensor Condition
Idling after warm-up Constant at between 50 and 700°C (122 and 1292°F) Normal
0°C (32°F) Open circuit
1000°C (1832°F) Short circuit


CONFIRMATION DRIVING PATTERN

P0545, P0546, P2032, P2033, P242C, P242D
DTC Detection Drive Pattern Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.

MONITOR DESCRIPTION

The ECM constantly monitors the output voltages from the exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.2 V and 4.95 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.

WIRING DIAGRAM

A276472
5.99,4.385 6.396,4.583 0.406,0.198 10 false ECM 5.667,3.01 6.104,3.208 0.438,0.198 10 false THCO 5.667,3.844 5.917,4.042 0.25,0.198 10 false E2 1.292,3.427 4.438,3.833 3.146,0.406 10 false No. 3 Exhaust Gas Temperature Sensor (B1S3) 5.656,1.771 6.094,1.969 0.438,0.198 10 false THCI 1.281,2.135 4.417,2.458 3.135,0.323 10 false No. 2 Exhaust Gas Temperature Sensor (B1S2) 5.219,0.542 5.594,0.708 0.375,0.167 10 false C111 5.354,0.365 5.563,0.552 0.208,0.188 10 false 17 1.292,1.948 1.688,2.135 0.396,0.188 10 false C122 1.292,3.229 1.646,3.406 0.354,0.177 10 false C123 1.292,0.896 4.083,1.302 2.792,0.406 10 false Exhaust Gas Temperature Sensor (B1S1) 1.292,0.719 1.667,0.906 0.375,0.188 10 false C121 1.969,0.406 2.094,0.573 0.125,0.167 10 false 2 2.75,0.396 2.896,0.604 0.146,0.208 10 false 1 5.656,0.542 6.094,0.74 0.438,0.198 10 false THCF 5.219,1.771 5.594,1.938 0.375,0.167 10 false C111 5.406,1.604 5.521,1.792 0.115,0.188 10 false 5 5.219,3.01 5.594,3.177 0.375,0.167 10 false C114 5.406,2.823 5.521,3.01 0.115,0.188 10 false 1 5.229,3.844 5.604,4.01 0.375,0.167 10 false C114 5.333,3.667 5.594,3.854 0.26,0.188 10 false 14 1.99,1.646 2.115,1.813 0.125,0.167 10 false 2 2.76,1.625 2.906,1.833 0.146,0.208 10 false 1 1.979,2.885 2.104,3.052 0.125,0.167 10 false 2 2.76,2.875 2.906,3.083 0.146,0.208 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

If DTC P242D is stored and the exhaust gas temperature sensor (B1S3) circuit is not malfunctioning, check if the DPF catalytic converter has melted as DTC P242D may be stored when the DPF catalytic converter melts and the exhaust gas temperature sensor (B1S3) is exposed to high temperatures.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (EXHAUST TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S1
Exhaust Temperature B1S2
Exhaust Temperature B1S3
50003 61 1061,1062,1063

d.

Read the value.

Standard:

Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after an engine speed of 3000 rpm is maintained for 1 minute.


Result:
Temperature Displayed Proceed to
0°C (32°F) (After warming up the engine) A
1000°C (1832°F) B
OK: Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after maintaining an engine speed of 3000 rpm for 1 minute after accelerating the engine from idling to 3000 rpm C


HINT:
·

If there is a short circuit, the intelligent tester will indicate 0°C (32°F).

·

If there is an open circuit, the intelligent tester will indicate 1000°C (1832°F).





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

6.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
A258901
0.604,3.354 0.99,3.552 0.385,0.198 0.604,3.656 1,3.854 0.396,0.198 0.604,3.948 1,4.146 0.396,0.198 0.25,0.198 0.563,0.396 0.313,0.198 10 false *1 2.333,0.177 2.542,0.333 0.208,0.156 10 false *2 2.438,1.052 2.781,1.219 0.344,0.167 10 false THCI 2.438,1.208 2.865,1.375 0.427,0.167 10 false THCO 2.438,1.354 2.844,1.542 0.406,0.188 10 false THCF 2.573,2.115 2.823,2.302 0.25,0.188 10 false E2 0.323,3.292 0.521,3.51 0.198,0.219 10 false *a 0.323,3.615 0.542,3.813 0.219,0.198 10 false *b 0.333,3.938 0.552,4.135 0.219,0.198 10 false *c 0.635,3.375 1.073,3.573 0.438,0.198 10 false C121 0.625,3.677 1.052,3.865 0.427,0.188 10 false C122 0.646,3.969 1.052,4.167 0.406,0.198 10 false C123
*1 Exhaust Gas Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Exhaust Gas Temperature Sensor (B1S1))
*b Front view of wire harness connector
(to No. 2 Exhaust Gas Temperature Sensor (B1S2))
*c Front view of wire harness connector
(to No. 3 Exhaust Gas Temperature Sensor (B1S3))


Disconnect the C121, C122 or C123 exhaust gas temperature sensor connector.


b.

Connect terminals 1 and 2 of the exhaust gas temperature sensor wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON and turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S1
Exhaust Temperature B1S2
Exhaust Temperature B1S3
50003 61 1061,1062,1063

f.

Read the value.

Standard:

1000°C (1832°F)



g.

Reconnect the exhaust gas temperature sensor connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE EXHAUST GAS TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
3.REPLACE EXHAUST GAS TEMPERATURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the exhaust gas temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C122-1 - C111-5 (THCI) Always Below 1 Ω
C122-2 - C114-14 (E2) Always Below 1 Ω
C123-1 - C114-1 (THCO) Always Below 1 Ω
C123-2 - C114-14 (E2) Always Below 1 Ω
C121-1 - C111-17 (THCF) Always Below 1 Ω
C121-2 - C114-14 (E2) Always Below 1 Ω



d.

Reconnect the exhaust gas temperature sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A246636
0.375,0.396 0.573,0.563 0.198,0.167 10 false *1 2.385,0.375 2.583,0.542 0.198,0.167 10 false *2 2.417,1.406 2.802,1.573 0.385,0.167 10 false THCI 2.417,1.563 2.875,1.729 0.458,0.167 10 false THCO 2.521,2.385 2.979,2.552 0.458,0.167 10 false E2 2.417,1.719 2.875,1.885 0.458,0.167 10 false THCF
*1 Exhaust Gas Temperature Sensor
*2 ECM


Disconnect the C121, C122 or C123 exhaust gas temperature sensor connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S1
Exhaust Temperature B1S2
Exhaust Temperature B1S3
50003 61 1061,1062,1063

e.

Read the value.

Standard:

0°C (32°F)



f.

Reconnect the exhaust gas temperature sensor connector.


g.

Reconnect the exhaust gas temperature sensor connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE EXHAUST GAS TEMPERATURE SENSOR

NG

8.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
7.REPLACE EXHAUST GAS TEMPERATURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the exhaust gas temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C122-1 or C111-5 (THCI) - Body ground Always 10 kΩ or higher
C123-1 or C114-1 (THCO) - Body ground Always 10 kΩ or higher
C121-1 or C111-17 (THCF) - Body ground Always 10 kΩ or higher



d.

Reconnect the exhaust gas temperature sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

9.REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Start the engine.


d.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END