Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2012.01–2012.04
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052600 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1243/43  Deceleration Sensor Stuck Malfunction  C1244/44  Open or Short in Deceleration Sensor Circuit  C1245/45  Deceleration Sensor Output Malfunction  C1279/79  Deceleration Sensor Output Voltage Malfunction (Test Mode DTC)  


DESCRIPTION

This sensor detects deceleration of the vehicle speed. The sensor signal is used in ABS control. If the sensor functions abnormally, the ABS warning light turns on.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1243/43 Deceleration Sensor Stuck Malfunction While the vehicle speed decreases from 30 km/h (18 mph) to 0 km/h (0 mph), the sensor signal does not change 16 times or more.
·

Deceleration sensor

·

Deceleration sensor circuit

·

Skid control ECU (Brake actuator assembly)


C1244/44 Open or Short in Deceleration Sensor Circuit One of the following conditions is met:
1.

Deceleration sensor signal value of -1.5 G or less or 1.5 G or more continues for 1.2 seconds or more.

2.

Deceleration sensor power supply terminal VGS voltage of 4.75 V or less or 5.25 V or higher continues for 1.2 seconds or more.

3.

Deceleration sensor signal momentary open occurs 7 times or more.


·

Deceleration sensor

·

Deceleration sensor circuit

·

Skid control ECU (Brake actuator assembly)


C1245/45 Deceleration Sensor Output Malfunction At a vehicle speed of 30 km/h (18 mph) or more, the difference between the forward and rearward G value calculated using sensor signals and the forward and rearward G value calculated using the vehicle speed exceeds 0.35 G for 60 seconds or more.
·

Deceleration sensor

·

Deceleration sensor circuit

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


C1279/79 Deceleration Sensor Output Voltage Malfunction (Test Mode DTC) Detected only during Test Mode.
·

Deceleration sensor

·

Sensor installation



WIRING DIAGRAM

C168911
1.292,1.75 1.385,1.906 0.094,0.156 10 false 1 6.063,1.854 6.604,2.281 0.542,0.427 10 false GL1 5.792,1.75 5.969,1.906 0.177,0.156 10 false 4 1.292,2.646 1.385,2.802 0.094,0.156 10 false 2 6.073,2.75 6.656,3.167 0.583,0.417 10 false GGND 5.792,2.667 5.969,2.823 0.177,0.156 10 false 7 1.292,0.844 1.385,1 0.094,0.156 10 false 3 6.073,0.948 6.542,1.323 0.469,0.375 10 false VGS 0.896,1.833 1.323,2.208 0.427,0.375 10 false GL1 0.76,2.74 1.313,3.094 0.552,0.354 10 false GGND 0.865,0.958 1.323,1.292 0.458,0.333 10 false VGS 5.76,0.854 5.958,1.01 0.198,0.156 10 false 28 0.146,4.063 0.417,4.219 0.271,0.156 10 false K5 0.146,4.219 1.615,4.552 1.469,0.333 10 false Deceleration Sensor 5.417,3.969 5.729,4.125 0.313,0.156 10 false A13 5.417,4.146 6.958,4.677 1.542,0.531 10 false Skid Control ECU (Brake Actuator Assembly) 3.458,3.135 4.115,3.375 0.656,0.24 10 false Shielded

CAUTION / NOTICE / HINT

NOTICE:
·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (DECELERATION SENSOR1)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Deceleration Sensor1 Deceleration sensor 1 reading Min.: -1.86 G
Max.: 1.85 G
Changes continuously during
acceleration/deceleration
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Deceleration Sensor1
50003 8 137

f.

Check that the deceleration value of the deceleration sensor displayed on the intelligent tester changes when the vehicle is tilted.

OK:

Changes continuously during acceleration/deceleration.



Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

3.INSPECT DECELERATION SENSOR
2.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 8

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 30 km/h (18 mph) or more for 60 seconds or more.


e.

Check if the same DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 8
Result:
Result Proceed to
DTC output A
DTC not output B




A

B

3.INSPECT DECELERATION SENSOR
a.

Turn the ignition switch off.




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - DECELERATION SENSOR)

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - DECELERATION SENSOR)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the deceleration sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-28 (VGS) - K5-3 (VGS) Always Below 1 Ω
A13-28 (VGS) - Body ground Always 10 kΩ or higher
A13-7 (GGND) - K5-2 (GGND) Always Below 1 Ω
A13-7 (GGND) - Body ground Always 10 kΩ or higher
A13-4 (GL1) - K5-1 (GL1) Always Below 1 Ω
A13-4 (GL1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR