Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2012.10–2013.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052600 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1248/48  Open Circuit in Rear Differential Lock  


DESCRIPTION

w/ Rear Differential Lock:

The skid control ECU (brake actuator assembly) monitors the rear differential lock position switch (No. 4 transfer indicator switch) and if the rear differential is locked, at which time the rear differential lock indicator light is illuminated, the skid control ECU (brake actuator assembly) prohibits the ABS.

At the same time, the skid control ECU (brake actuator assembly) illuminates the ABS warning light.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1248/48 Open Circuit in Rear Differential Lock At a vehicle speed of 50 km/h (31 mph) or more, 3 seconds or more elapse after the rear differential changes from free to lock.
HINT:

For vehicles without rear differential lock, this DTC may be stored due to an EXI2 terminal circuit malfunction.


·

w/ Rear Differential Lock:

·

Rear differential lock position switch (No. 4 transfer indicator switch)

·

Differential lock system


·

EXI2 terminal circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C237168
5.469,0.896 5.938,1.063 0.469,0.167 10 false EXI2 5.031,0.896 5.365,1.052 0.333,0.156 10 false 22*2 4.135,0.823 4.417,0.99 0.281,0.167 10 false 9*2 2.24,0.823 2.458,1.01 0.219,0.188 10 false 21 2.573,1.219 3.979,1.438 1.406,0.219 10 false Rear Differential Lock 4.021,1.031 4.333,1.271 0.313,0.24 10 false G20 2.323,1.677 4.281,1.854 1.958,0.177 10 false Combination Meter Assembly 0.635,1.021 1.604,1.229 0.969,0.208 10 false from IG Circuit 2.427,2.573 2.708,2.74 0.281,0.167 10 false L8 2.427,2.74 4.365,3.385 1.938,0.646 10 false Rear Differential Lock Position Switch (No. 4 Transfer Indicator Switch)*2 3.156,2.208 3.313,2.365 0.156,0.156 10 false 2 2.313,2.219 2.469,2.375 0.156,0.156 10 false 1 5.167,2.719 5.448,2.885 0.281,0.167 10 false A13 5.167,2.948 6.698,3.375 1.531,0.427 10 false Skid Control ECU (Brake Actuator Assembly) 1.469,0.438 2.417,0.604 0.948,0.167 10 false from IG Circuit 5.479,0.271 5.948,0.438 0.469,0.167 10 false EXI2 5.031,0.333 5.344,0.49 0.313,0.156 10 false 22*1 0.115,5.135 2.021,5.302 1.906,0.167 10 false *1: w/o Rear Differential Lock 0.115,5.49 2.021,5.656 1.906,0.167 10 false *2: w/ Rear Differential Lock 0.271,4.406 0.563,4.604 0.292,0.198 10 false K28 0.271,4.604 5.042,4.865 4.771,0.26 10 false Rear Differential Lock ECU (No. 2 4 Wheel Drive Control ECU)*2 2.448,3.875 2.677,4.115 0.229,0.24 10 false 1 2.01,3.875 2.375,4.073 0.365,0.198 10 false RLP 2.188,1.031 2.51,1.219 0.323,0.188 10 false G19 2.521,0.917 2.802,1.083 0.281,0.167 10 false IG+ 3.844,0.927 3.99,1.094 0.146,0.167 10 false L

CAUTION / NOTICE / HINT

NOTICE:
·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (EXI2 TERMINAL)
a.
C117862
1.521,0.656 1.865,0.917 0.344,0.26 2.438,2.823 2.604,2.823 2.604,2.823 2.615,2.063 false 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 1.583,0.698 1.99,0.938 0.406,0.24 10 false A13 2.115,2.76 2.521,3 0.406,0.24 10 false EXI2
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


w/ Rear Differential Lock: Set the vehicle to the rear differential free state.


b.

Turn the ignition switch off.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-22 (EXI2) - Body ground Ignition switch ON 11 to 14 V


Result:
Result Proceed to
OK A
NG (w/ Rear Differential Lock) B
NG (w/o Rear Differential Lock) C




A

2.RECONFIRM DTC

B

3.INSPECT REAR DIFFERENTIAL LOCK POSITION SWITCH

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 8

b.

Turn the ignition switch off.


c.

Start the engine.


d.

w/ Rear Differential Lock: Set the vehicle to the rear differential free state.


e.

Drive the vehicle at a speed of 50 km/h (31 mph) or more for 3 seconds or more.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 8
Result:
Result Proceed to
DTC output A
DTC not output B




A

B

3.INSPECT REAR DIFFERENTIAL LOCK POSITION SWITCH
a.

Turn the ignition switch off.


b.

Remove the rear differential lock position switch (No. 4 transfer indicator switch).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH(w/ Differential Lock)>REMOVAL


c.

Inspect the rear differential lock position switch (No. 4 transfer indicator switch).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>DIFFERENTIAL SYSTEM(w/ Differential Lock)>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (EXI2 TERMINAL CIRCUIT)

NG

4.CHECK HARNESS AND CONNECTOR (EXI2 TERMINAL CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the rear differential lock position switch (No. 4 transfer indicator switch) connector.


c.

Disconnect the rear differential lock ECU (No. 2 4 wheel drive control ECU) connector.


d.

Disconnect the skid control ECU (brake actuator assembly) connector.


e.

Disconnect the G20 combination meter connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-22 (EXI2) - L8-2 Always Below 1 Ω
A13-22 (EXI2) - G20-9 (L) Always Below 1 Ω
A13-22 (EXI2) - K28-1 (RLP) Always Below 1 Ω
A13-22 (EXI2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR