Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2012.01–2012.04
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052600 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1283/83  L4 Position Switch Malfunction (Test Mode DTC)  


DESCRIPTION

DTC C1283/83 is output only in Test Mode.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1283/83 L4 Position Switch Malfunction (Test Mode DTC) No signal is input to the EXI4 terminal of the skid control ECU.
·

L4 position switch (No. 1 transfer indicator switch)

·

EXI4 terminal circuit

·

Skid control ECU (Brake actuator assembly)



*C1283/83: for 4WD

HINT:

The codes in this table are output only in Test Mode.


WIRING DIAGRAM

C239087
0.594,1.729 2.271,2.083 1.677,0.354 10 Skid Control ECU (Brake Actuator Assembly) 4.552,1.688 6.49,2.125 1.938,0.438 10 L4 Position Switch (No. 1 Transfer Indicator Switch) 0.604,1.563 1,1.75 0.396,0.188 10 A13 4.531,1.51 4.875,1.677 0.344,0.167 10 C29 2.26,1.052 2.438,1.229 0.177,0.177 10 3 4.438,1.042 4.573,1.198 0.135,0.156 10 1 5.875,1.052 6,1.229 0.125,0.177 10 2 1.781,1.177 2.167,1.344 0.385,0.167 10 EXI4

CAUTION / NOTICE / HINT

NOTICE:
·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK EXI4 TERMINAL CIRCUIT
a.

Set the vehicle to the L4 state using the transfer shift lever.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-3 (EXI4) - Body ground Transfer shift position L4 Below 1 Ω



d.

Connect the skid control ECU (brake actuator assembly) connector.


e.

Set the vehicle to the H2 state using the transfer shift lever.


f.

Disconnect the skid control ECU (brake actuator assembly) connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-3 (EXI4) - Body ground Transfer shift position H2 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK TEST MODE DTC

NG

3.CHECK HARNESS AND CONNECTOR (EXI4 TERMINAL CIRCUIT)
2.CHECK TEST MODE DTC
a.

Switch the vehicle to Test Mode, perform the H2 to L4 shift operation check, and then check that DTC C1283/83 is not stored.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE

Result:
Result Proceed to
DTC is stored A
DTC is not stored B




A

B

3.CHECK HARNESS AND CONNECTOR (EXI4 TERMINAL CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the L4 position switch (No. 1 transfer indicator switch) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-3 (EXI4) - C29-1 Always Below 1 Ω
A13-3 (EXI4) - Body ground Always 10 kΩ or higher
C29-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT L4 POSITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT L4 POSITION SWITCH
a.

Turn the ignition switch off.


b.

Remove the L4 position switch (No. 1 transfer indicator switch).

Click hereDrivetrain>VF2A TRANSFER / 4WD / AWD>TRANSFER INDICATOR SWITCH>REMOVAL


c.

Inspect the L4 position switch (No. 1 transfer indicator switch).

Click hereDrivetrain>VF2A TRANSFER / 4WD / AWD>TRANSFER INDICATOR SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 1 TRANSFER INDICATOR SWITCH