Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2012.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1232  Acceleration Sensor Stuck Malfunction  C1243  Acceleration Sensor Stuck Malfunction  C1245  Acceleration Sensor Output Malfunction  C1279  Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate assembly via the CAN communication system.

The yaw rate sensor assembly has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is trouble in the bus lines between the yaw rate sensor assembly and the CAN communication system, DTCs U0123 (Lost Communication with Yaw Rate Sensor Module) and U0124 (Lost Communication with Lateral Acceleration Sensor Module) are stored.

DTC C1232, C1243, C1245 and C1279 are also stored when calibration has not been completed.

DTC C1279 can be cleared when the yaw rate sensor assembly sends a yaw rate and/or acceleration signal or Test Mode ends. DTC C1279 is stored only in Test Mode.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1232 Acceleration Sensor Stuck Malfunction At a vehicle speed of 10 km/h (6 mph) or more, either GL1 or GL2 (input signal) does not change for 30 seconds or more.
·

Acceleration sensor (Yaw rate sensor assembly)

·

Yaw rate sensor assembly circuit


C1243 Acceleration Sensor Stuck Malfunction While the vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), the condition that the values of GL1 and GL2 do not change by 0.0294 G or more occurs 16 times or more.
·

Acceleration sensor (Yaw rate sensor assembly)

·

Yaw rate sensor assembly circuit


C1245 Acceleration Sensor Output Malfunction At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
·

Acceleration sensor (Yaw rate sensor assembly)

·

Yaw rate sensor assembly circuit

·

Sensor installation


C1279 Acceleration Sensor Output Voltage Malfunction (Test Mode DTC) Stored during Test Mode.
·

Acceleration sensor (Yaw rate sensor assembly)

·

Sensor installation



WIRING DIAGRAM

C185399
0.365,1.521 3.323,1.771 2.958,0.25 10 false Skid Control ECU (Brake Actuator Assembly) 0.76,2.385 3.031,2.563 2.271,0.177 10 false : CAN Communication System 4.813,2.229 6.75,2.469 1.938,0.24 10 false Yaw Rate Sensor Assembly 0.365,1.344 0.677,1.51 0.313,0.167 10 false A36 3.719,0.385 4.865,0.531 1.146,0.146 10 false ECU-IG&GAUGE 1.958,0.188 3.031,0.385 1.073,0.198 10 false from IG1 Circuit 5.594,0.76 5.885,1 0.292,0.24 10 false IG 6.021,1.406 6.417,1.573 0.396,0.167 10 false GND 5.75,0.49 5.938,0.677 0.188,0.188 10 false 4 6.479,1.271 6.708,1.49 0.229,0.219 10 false 1 4.813,2.073 5.156,2.229 0.344,0.156 10 false K21

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the yaw rate sensor assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



HINT:

When DTC U0123 and/or U0124 is output together with DTC C1232, C1243 and/or C1245, inspect and repair the trouble areas indicated by DTC U0123 and/or U0124 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073).


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 30 km/h (19 mph) or more, turn the steering wheel and decelerate (depress the brake pedal) the vehicle.


e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON again and check that no CAN communication system DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR


g.

Check if DTCs for zero point calibration of the yaw rate sensor (C1210) or for zero point calibration of the acceleration sensor (C1336) are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC relating to yaw rate and acceleration sensor is output A
DTC relating to CAN communication system is output B
DTC C1210 and/or C1336 is output C




A

2.CHECK YAW RATE SENSOR ASSEMBLY INSTALLATION

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

2.CHECK YAW RATE SENSOR ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate sensor assembly is installed properly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND ACCELERATION SENSOR(w/ VSC)>INSTALLATION

OK:

The sensor is tightened to the specified torque.

The sensor is not installed at an angle.



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE AND RESISTANCE (IG, GND TERMINAL)

NG

3.CHECK TERMINAL VOLTAGE AND RESISTANCE (IG, GND TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the yaw rate sensor assembly connector.


c.
C208309
0.167,1.021 0.5,1.271 0.333,0.25 0.74,1.667 1.198,1.198 false 2.417,1.719 1.813,1.198 false 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.219,1.063 0.594,1.323 0.375,0.26 10 false K21 0.573,1.719 0.948,1.979 0.375,0.26 10 false GND 2.396,1.75 2.771,2.01 0.375,0.26 10 false IG
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K21-4 (IG) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR