Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.10–2013.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1241  Low Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits brake control operation.

This DTC is stored when the IG1 terminal voltage drops below the threshold due to a malfunction in the power supply or charging circuit, such as the battery or generator circuit, etc.

The DTC is cleared when the IG1 terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1241 Low Power Supply Voltage Malfunction One of the following conditions is met:
1.

At a vehicle speed of 3 km/h (2 mph) or more, the IG1 terminal voltage is below 9.5 V for 10 seconds or more.

2.

When the solenoid relay remains on and the IG1 terminal voltage is below 9.5 V, the relay contact is open for 0.22 seconds or more.

3.

With the IG1 terminal voltage at 9.5 V or less, the vehicle speed sensor power supply decreases for 60 seconds or more.

4.

When the motor relay and fail-safe relay are on, the voltage at terminal IG1 is below 9.5 V and the actuator pump motor is off for 0.2 seconds or more.


·

ECU-IG&GAUGE fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C194309
0.979,1.083 2.01,1.271 1.031,0.188 10 false from IG1 Circuit 2.875,1.271 4.073,1.5 1.198,0.229 10 false ECU-IG&GAUGE 5.24,1.073 5.698,1.271 0.458,0.198 10 false IG1 4.927,0.979 5.208,1.167 0.281,0.188 10 false 34 5.24,1.448 5.698,1.646 0.458,0.198 10 false GND1 5.01,1.354 5.219,1.542 0.208,0.188 10 false 1 5.115,2.698 5.521,2.875 0.406,0.177 10 false A36 5.115,2.885 6.76,3.26 1.646,0.375 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.
C199357
0.094,0.958 0.479,1.24 0.385,0.281 2.01,1.938 2.094,1.938 2.094,1.938 2.302,1.385 false 0.135,0.063 0.448,0.219 0.313,0.156 10 false *a 0.167,1.021 0.479,1.177 0.313,0.156 10 false A36 1.76,1.854 2.156,2.094 0.396,0.24 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A36-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-1 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B