Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1405 | Open or Short in Front Speed Sensor RH Circuit | Either condition is met:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2.
With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Front speed sensor RH ·
Speed sensor circuit ·
Skid control ECU (Brake actuator assembly) |
| C1406 | Open or Short in Front Speed Sensor LH Circuit | Either condition is met:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2.
With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Front speed sensor LH ·
Speed sensor circuit ·
Skid control ECU (Brake actuator assembly) |
DTC C1405 is for the front speed sensor RH.
DTC C1406 is for the front speed sensor LH.
After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
Before disconnecting the connector, make sure that there are no problems with the connection.
After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Speed Open | Front speed sensor RH open circuit detection | Error or Normal | Normal | - |
| FL Speed Open | Front speed sensor LH open circuit detection | Error or Normal | Normal | - |
| Tester Display |
|---|
| FR Speed Open |
| FL Speed Open |
Normal (there are no momentary interruptions).
Perform the above inspection before removing the sensor or disconnecting a connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Actual wheel speed | No large fluctuations when driving at a constant speed. |
| FL Wheel Speed | Front speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Actual wheel speed | No large fluctuations when driving at a constant speed. |
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
Check the speed value output from the speed sensor displayed on the intelligent tester.
Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK
The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-7 (FR+) - A11-1 (FR+) | Always | Below 1 Ω |
| A36-7 (FR+) - Body ground | Always | 10 kΩ or higher |
| A36-6 (FR-) - A11-2 (FR-) | Always | Below 1 Ω |
| A36-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-19 (FL+) - A12-1 (FL+) | Always | Below 1 Ω |
| A36-19 (FL+) - Body ground | Always | 10 kΩ or higher |
| A36-18 (FL-) - A12-2 (FL-) | Always | Below 1 Ω |
| A36-18 (FL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the skid control ECU (brake actuator assembly) connector.
Disconnect the speed sensor connector.
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector
(to Front Speed Sensor) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A11-1 (FR+) - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A12-1 (FL+) - Body ground | Ignition switch ON | 8 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 4WD and Pre-Runner)>REMOVAL
NG