Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2012.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1407  Open or Short in Rear Speed Sensor RH Circuit  C1408  Open or Short in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271).

DTC No. Detection Item DTC Detection Condition Trouble Area
C1407 Open or Short in Rear Speed Sensor RH Circuit Either condition is met:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor RH

·

Speed sensor circuit

·

Skid control ECU (Brake actuator assembly)


C1408 Open or Short in Rear Speed Sensor LH Circuit Either condition is met:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor LH

·

Speed sensor circuit

·

Skid control ECU (Brake actuator assembly)



HINT:
·

DTC C1407 is for the rear speed sensor RH.

·

DTC C1408 is for the rear speed sensor LH.



WIRING DIAGRAM

C149728
0.488,1.014 1.272,1.325 0.785,0.311 10 Rear Speed Sensor LH 0.459,2.249 1.246,2.564 0.787,0.315 10 Rear Speed Sensor RH 5.182,3.016 6.948,3.449 1.766,0.433 10 Skid Control ECU (Brake Actuator Assembly) 5.581,0.665 5.965,0.809 0.385,0.143 10 RL- 5.581,1.157 5.918,1.297 0.337,0.141 10 RL+ 5.581,2.363 5.954,2.506 0.373,0.142 10 RR+ 5.581,1.876 6.001,2.022 0.421,0.146 10 RR- 2.293,2.247 2.391,2.395 0.098,0.148 10 2 2.293,0.567 2.391,0.718 0.098,0.15 10 1 2.293,1.047 2.388,1.195 0.095,0.148 10 2 2.293,1.772 2.391,1.923 0.098,0.15 10 1 0.488,0.847 0.756,1.004 0.268,0.157 10 L3 0.459,2.09 0.845,2.247 0.386,0.157 10 L7 5.255,1.765 5.432,1.914 0.176,0.149 10 16 5.255,2.255 5.444,2.404 0.189,0.149 10 17 5.33,1.067 5.452,1.209 0.122,0.142 10 5 5.33,0.581 5.445,0.727 0.115,0.146 10 4 5.182,2.843 5.446,3.024 0.265,0.182 10 A36

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open circuit detection Error or Normal Normal -
RL Speed Open Rear speed sensor LH open circuit detection Error or Normal Normal -
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
RL Speed Open
50003 105 202,203
OK:

Normal (there are no momentary interruptions).


HINT:

Perform the above inspection before removing the sensor or disconnecting a connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
2.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

f.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
3.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A36-17 (RR+) - L7-2 Always Below 1 Ω
A36-17 (RR+) - Body ground Always 10 kΩ or higher
A36-16 (RR-) - L7-1 Always Below 1 Ω
A36-16 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A36-5 (RL+) - L3-2 Always Below 1 Ω
A36-5 (RL+) - Body ground Always 10 kΩ or higher
A36-4 (RL-) - L3-1 Always Below 1 Ω
A36-4 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (SENSOR POWER SUPPLY VOLTAGE TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (SENSOR POWER SUPPLY VOLTAGE TERMINAL)
a.

Turn the ignition switch off.


b.

Connect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the speed sensor connector.


d.
C238771
0.823,0.292 1.104,0.49 0.281,0.198 2.406,0.292 2.688,0.49 0.281,0.198 2.719,0.323 3.031,0.479 0.313,0.156 10 false *A 1.135,0.323 1.448,0.479 0.313,0.156 10 false *B 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 0.896,0.313 1.135,0.521 0.24,0.208 10 false L3 2.479,0.313 2.719,0.521 0.24,0.208 10 false L7
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
L7-2 - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
L3-2 - Body ground Ignition switch ON 8 to 14 V



Result:
Proceed to
OK
NG



OK

NG