Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.04–2012.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) has an open detection circuit, which stores this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC No. Detection Item DTC Detection Condition Trouble Area
C1425 Open in Stop Light Switch Circuit When the IG1 terminal voltage is between 9.5 and 17.4 V, an open in the stop light circuit continues for 0.3 seconds or more.
·

Stop light LH and RH circuit

·

STP terminal circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C237301
0.802,0.823 2.26,1.01 1.458,0.188 10 false from Stop Light Switch 4.615,0.719 4.792,0.906 0.177,0.188 10 false 2 4.844,0.719 5.198,0.958 0.354,0.24 10 false STP 5.552,1.271 6.26,1.781 0.708,0.51 10 false Open Detection Circuit 4.865,2.094 5.344,2.292 0.479,0.198 10 false GND1 4.635,1.948 4.781,2.135 0.146,0.188 10 false 1 2.719,1.802 2.958,1.99 0.24,0.188 10 false L1 0.927,2.021 2.167,2.563 1.24,0.542 10 false Rear Combination Light Assembly LH (Stop Light LH) 0.917,1.823 1.156,2.01 0.24,0.188 10 false L2 2.729,2.01 3.958,2.552 1.229,0.542 10 false Rear Combination Light Assembly RH (Stop Light RH) 0.479,1.885 0.635,2.073 0.156,0.188 10 false 4 2.271,1.896 2.427,2.083 0.156,0.188 10 false 4 0.469,2.729 0.625,2.917 0.156,0.188 10 false 3 2.26,2.719 2.417,2.906 0.156,0.188 10 false 3 4.781,2.844 5.083,3.01 0.302,0.167 10 false A36 4.781,3.031 6.406,3.406 1.625,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 0.594,2.125 0.75,2.313 0.156,0.188 10 false B 0.573,2.49 0.729,2.677 0.156,0.188 10 false E 2.385,2.135 2.542,2.323 0.156,0.188 10 false B 2.385,2.479 2.542,2.667 0.156,0.188 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop light LH and RH come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (STP TERMINAL)

NG

GO TO LIGHTING SYSTEM (PROBLEM SYMPTOMS TABLE)

2.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.
C199357
0.156,0.99 0.458,1.208 0.302,0.219 1.292,0.844 1.563,0.219 1.563,0.219 1.76,0.219 false 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 1.792,0.135 2.177,0.385 0.385,0.25 10 false STP 0.188,1.021 0.573,1.271 0.385,0.25 10 false A36
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-2 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Depress the brake pedal.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B