The brake pedal load sensing switch operates when the brake pedal is depressed with a force exceeding a predetermined level.
The skid control ECU (brake actuator assembly) detects if the brake pedal is depressed or not via this circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1429 | Open or Short in Brake Pedal Load Sensing Switch | An open or short in the brake pedal load sensing switch continues for 0.3 seconds or more. | ·
Brake pedal load sensing switch (Brake with switch pedal sub-assembly) ·
Brake pedal load sensing switch circuit ·
Skid control ECU (Brake actuator assembly) |
After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Before disconnecting the connector, make sure that there are no problems with the connection.
After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
When DTC C1425 is output together with DTC C1429, inspect and repair the trouble areas indicated by DTC C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425).
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch | ON or OFF | ON: Brake pedal depressed beyond specified point
OFF: Brake pedal not depressed beyond specified point |
- |
| Tester Display |
|---|
| Brake Pedal Load Sensing SW |
Check that the brake pedal load sensing switch display observed on the intelligent tester changes according to the brake pedal operation.
The intelligent tester displays ON or OFF according to brake pedal operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Depress the brake pedal several times.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
| *1 | Brake Pedal Load Sensing Switch | *2 | Brake with Switch Pedal Sub-assembly |
| *a | Component without harness connected
(Brake Pedal Load Sensing Switch) |
*b | Brake Pedal Released (Closed) |
| *c | Brake Pedal Depressed (Open) | - | - |
Do not remove the brake pedal load sensing switch from the brake with switch pedal sub-assembly.
When there is a malfunction in the brake pedal load sensing switch, replace the brake with switch pedal sub-assembly.
Turn the ignition switch off.
Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 - 1 | Brake pedal depressed | 950 to 1050 Ω |
| Brake pedal released | 203 to 223 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-27 (FSW+) - A35-2 | Always | Below 1 Ω |
| A36-27 (FSW+) - Body ground | Always | 10 kΩ or higher |
| A35-1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG