Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2012.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1429  Open or Short in Brake Pedal Load Sensing Switch  


DESCRIPTION

The brake pedal load sensing switch operates when the brake pedal is depressed with a force exceeding a predetermined level.

The skid control ECU (brake actuator assembly) detects if the brake pedal is depressed or not via this circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1429 Open or Short in Brake Pedal Load Sensing Switch An open or short in the brake pedal load sensing switch continues for 0.3 seconds or more.
·

Brake pedal load sensing switch (Brake with switch pedal sub-assembly)

·

Brake pedal load sensing switch circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C194456
2.208,1.281 2.365,1.479 0.156,0.198 10 false 1 4.115,1.281 4.271,1.479 0.156,0.198 10 false 2 5.563,1.281 6,1.635 0.438,0.354 10 false 27 5.813,1.385 6.406,1.708 0.594,0.323 10 false FSW+ 2.271,2.281 4.938,3.094 2.667,0.813 10 false Brake Pedal Load Sensing Switch (Brake with Switch Pedal Sub-assembly) 5.417,3.042 7.042,3.573 1.625,0.531 10 false Skid Control ECU (Brake Actuator Assembly) 5.417,2.875 5.781,3.167 0.365,0.292 10 false A36 2.292,2.125 2.823,2.438 0.531,0.313 10 false A35

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



HINT:

When DTC C1425 is output together with DTC C1429, inspect and repair the trouble areas indicated by DTC C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (BRAKE PEDAL LOAD SENSING SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Pedal Load Sensing SW Brake pedal load sensing switch ON or OFF ON: Brake pedal depressed beyond specified point
OFF: Brake pedal not depressed beyond specified point
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Brake Pedal Load Sensing SW
50003 105 39

f.

Check that the brake pedal load sensing switch display observed on the intelligent tester changes according to the brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH
2.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Depress the brake pedal several times.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B




A

B

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH
C190633
1.021,1.688 1.021,1.469 1.021,1.469 1.969,1.094 false 3.167,2.771 3.167,2.667 3.167,2.667 2.625,2.573 false 4.594,1.792 4.781,1.792 4.781,1.792 5.219,2.427 false 4.74,3.104 4.844,3.104 4.844,3.104 5.167,2.49 false 0.958,1.719 1.271,1.875 0.313,0.156 10 false *1 3.104,2.813 3.417,2.969 0.313,0.156 10 false *2 4.99,0.76 5.292,1 0.302,0.24 10 false *a 4.417,1.698 4.688,2 0.271,0.302 10 false *b 4.573,3.01 4.896,3.292 0.323,0.281 10 false *c 4.656,2.323 4.896,2.635 0.24,0.313 10 false 2 6.031,2.313 6.271,2.625 0.24,0.313 10 false 1
*1 Brake Pedal Load Sensing Switch *2 Brake with Switch Pedal Sub-assembly
*a Component without harness connected
(Brake Pedal Load Sensing Switch)
*b Brake Pedal Released (Closed)
*c Brake Pedal Depressed (Open) - -


NOTICE:
·

Do not remove the brake pedal load sensing switch from the brake with switch pedal sub-assembly.

·

When there is a malfunction in the brake pedal load sensing switch, replace the brake with switch pedal sub-assembly.



a.

Turn the ignition switch off.


b.

Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 1 Brake pedal depressed 950 to 1050 Ω
Brake pedal released 203 to 223 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)

NG

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-27 (FSW+) - A35-2 Always Below 1 Ω
A36-27 (FSW+) - Body ground Always 10 kΩ or higher
A35-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR