Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.01–2012.04
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1436  Yaw Rate Sensor Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate sensor assembly via the CAN communication system.

If there is trouble in the bus lines between the yaw rate sensor assembly and the CAN communication system, DTCs U0123 (Lost Communication with Yaw Rate Sensor Module) and U0124 (Lost Communication with Lateral Acceleration Sensor Module) are stored.

DTC C1436 is also stored when calibration is not completed.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1436 Yaw Rate Sensor Malfunction Either condition is met:
1.

With the vehicle stationary, the yaw rate and acceleration sensor output value is not 0 deg/s.

2.

An abnormal comparison value.


Yaw rate sensor assembly

CAUTION / NOTICE / HINT

NOTICE:

After replacing the yaw rate sensor assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:

When DTC U0123 and/or U0124 is output together with DTC C1436, inspect and repair the trouble areas indicated by DTC U0123 and/or U0124 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (YAW RATE SENSOR, YAW RATE SENSOR 2)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Yaw Rate Sensor Yaw rate sensor Min.: -128°/s
Max.: 127°/s
Vehicle stationary: 0°/s
Right turn: -128 to 0°/s
Left turn: 0 to 127°/s
-
Yaw Rate Sensor2 Yaw rate sensor 2 Min.: -128°/s
Max.: 127°/s
Vehicle stationary: 0°/s
Right turn: -128 to 0°/s
Left turn: 0 to 127°/s
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Yaw Rate Sensor
Yaw Rate Sensor2
50003 105 24,25

f.

Check the yaw rate sensor output value displayed on the intelligent tester.

Result:
Result Proceed to
NG (Yaw rate sensor output value is 0°/s when vehicle is stationary, but value fluctuates when turning) A
NG (Yaw rate sensor output value is not 0°/s when vehicle is stationary) B
OK C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

2.CHECK YAW RATE SENSOR ASSEMBLY INSTALLATION

B

C

2.CHECK YAW RATE SENSOR ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate sensor assembly is installed properly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND ACCELERATION SENSOR(w/ VSC)>INSTALLATION

OK:

The sensor is tightened to the specified torque.

The sensor is not installed at an angle.



Result:
Proceed to
OK
NG



OK

NG