This DTC is output when one of the following occurs: 1) the ECM detects errors in its own communications with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; or 3) the ECU communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no transponder key ECU DTCs are present. If present, troubleshoot the transponder key ECU DTCs first.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2799 | Engine Immobiliser System Malfunction | Either condition is met (1 trip detection logic*1):
·
A malfunction occurs in the communication or communication lines between the ECM and transponder key ECU assembly. ·
A communication code cannot be verified during communication between the ECM and transponder key ECU assembly. |
·
Harness or connector ·
Transponder key ECU assembly ·
ECM ·
Telephone transceiver assembly*4 |
Detection Enabling Condition (DTC Output Confirmation Operation)
Either condition is met: ·
Within 10 seconds of an engine start operation being performed (with the shift lever in P and the brake pedal [for Automatic Transmission] or clutch pedal [for Manual Transmission] depressed, turn the ignition switch to ON). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds). ·
10 seconds after the ignition switch is turned to ON after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the ignition switch being turned to ON, and DTCs are stored after 6 seconds). |
*1: Only output while a malfunction is present.
*2: w/ Blocking System
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine cannot be started. | - |
| DTC Code | Data List and Active Test |
|---|---|
| B2799 | - |
The fixed 12 V power source voltage in the ECM is output through a resistance from terminal IMI. The transponder key ECU assembly grounds or does not ground this power source voltage accordingly.
The fixed 12 V power source voltage in the transponder key ECU assembly is output through a resistance from terminal EFII. The ECM grounds or does not ground this power source voltage accordingly.
When replacing the transponder key ECU assembly, ECM or telephone transceiver assembly (w/ Blocking System), refer to the Service Bulletin.
After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
When DTC B1587 and B2799 are output simultaneously, perform troubleshooting for DTC B2799 first.
After troubleshooting for this DTC, make sure B2799 is not present. If present, troubleshoot the blocking system DTCs next.
Clear the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR
DTC B2799 is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Blocking System) | B |
| NG (w/o Blocking System) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Check the blocking system setting.
Check with the customer's contacted service provider to determine whether the blocking system is set.
Request that the customer have the service provider unset the blocking system.
| Result | Proceed to |
|---|---|
| Blocking system is unset. | A |
| Blocking system is set | B |
A
B
Reregister the ECU - ECM communication ID (Refer to Service Bulletin).
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR
DTC B2799 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Check that the connectors are properly connected to the ECM and transponder key ECU assembly.
Connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G26 transponder key ECU assembly connector.
Disconnect the G38*1, G88*2, G146*3, G148*4, G154*5 or G156*6 ECM connector.
*1: for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF)
*2: for 2TR-FE
*3: for 2TR-FBE
*4: 1KD-FTV (for DPF), 2KD-FTV (for DPF)
*5: for 1GR-FE
*6: for 1KD-FTV (for i-ART)
w/ Blocking System:
Disconnect the G144 telephone transceiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) - G38-30 (IMI) | Always | Below 1 Ω |
| G26-12 (EFII) - G38-29 (IMO) | Always | Below 1 Ω |
| G26-13 (EFIO) or G38-30 (IMI) - Body ground | Always | 10 kΩ or higher |
| G26-12 (EFII) or G38-29 (IMO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Condition |
|---|---|---|
| G26-13 (EFIO) - G144-2 (BLK4) | Always | Below 1 Ω |
| G26-12 (EFII) - G144-1 (BLK1) | Always | Below 1 Ω |
| G144-8 (BLK3) - G38-30 (IMI) | Always | Below 1 Ω |
| G144-7 (BLK2) - G38-29 (IMO) | Always | Below 1 Ω |
| G26-13 (EFIO) or G144-2 (BLK4) - Body ground | Always | 10 kΩ or higher |
| G26-12 (EFII) or G144-1 (BLK1) - Body ground | Always | 10 kΩ or higher |
| G144-8 (BLK3) or G38-30 (IMI) - Body ground | Always | 10 kΩ or higher |
| G144-7 (BLK2) or G38-29 (IMO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) - G88-16 (IMI) | Always | Below 1 Ω |
| G26-12 (EFII) - G88-15 (IMO) | Always | Below 1 Ω |
| G26-13 (EFIO) or G88-16 (IMI) - Body ground | Always | 10 kΩ or higher |
| G26-12 (EFII) or G88-15 (IMO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) - G146-31 (IMI) | Always | Below 1 Ω |
| G26-12 (EFII) - G146-32 (IMO) | Always | Below 1 Ω |
| G26-13 (EFIO) or G146-31 (IMI) - Body ground | Always | 10 kΩ or higher |
| G26-12 (EFII) or G146-32 (IMO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) - G144-2 (BLK4) | Always | Below 1 Ω |
| G26-12 (EFII) - G144-1 (BLK1) | Always | Below 1 Ω |
| G144-8 (BLK3) - G146-31 (IMI) | Always | Below 1 Ω |
| G144-7 (BLK2) - G146-32 (IMO) | Always | Below 1 Ω |
| G26-13 (EFIO) or G144-2 (BLK4) - Body ground | Always | 10 kΩ or higher |
| G26-12 (EFII) or G144-1 (BLK1) - Body ground | Always | 10 kΩ or higher |
| G144-8 (BLK3) or G146-31 (IMI) - Body ground | Always | 10 kΩ or higher |
| G144-7 (BLK2) or G146-32 (IMO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) - G148-28 (IMI) | Always | Below 1 Ω |
| G26-12 (EFII) - G148-29 (IMO) | Always | Below 1 Ω |
| G26-13 (EFIO) or G148-28 (IMI) - Body ground | Always | 10 kΩ or higher |
| G26-12 (EFII) or G148-29 (IMO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) - G144-2 (BLK4) | Always | Below 1 Ω |
| G26-12 (EFII) - G144-1 (BLK1) | Always | Below 1 Ω |
| G144-8 (BLK3) - G148-28 (IMI) | Always | Below 1 Ω |
| G144-7 (BLK2) - G148-29 (IMO) | Always | Below 1 Ω |
| G26-13 (EFIO) or G144-2 (BLK4) - Body ground | Always | 10 kΩ or higher |
| G26-12 (EFII) or G144-1 (BLK1) - Body ground | Always | 10 kΩ or higher |
| G144-8 (BLK3) or G148-28 (IMI) - Body ground | Always | 10 kΩ or higher |
| G144-7 (BLK2) or G148-29 (IMO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) - G154-16 (IMI) | Always | Below 1 Ω |
| G26-12 (EFII) - G154-15 (IMO) | Always | Below 1 Ω |
| G26-13 (EFIO) or G154-16 (IMI) - Body ground | Always | 10 kΩ or higher |
| G26-12 (EFII) or G154-15 (IMO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) - G156-28 (IMI) | Always | Below 1 Ω |
| G26-12 (EFII) - G156-29 (IMO) | Always | Below 1 Ω |
| G26-13 (EFIO) or G156-28 (IMI) - Body ground | Always | 10 kΩ or higher |
| G26-12 (EFII) or G156-29 (IMO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) - G144-2 (BLK4) | Always | Below 1 Ω |
| G26-12 (EFII) - G144-1 (BLK1) | Always | Below 1 Ω |
| G144-8 (BLK3) - G156-28 (IMI) | Always | Below 1 Ω |
| G144-7 (BLK2) - G156-29 (IMO) | Always | Below 1 Ω |
| G26-13 (EFIO) or G144-2 (BLK4) - Body ground | Always | 10 kΩ or higher |
| G26-12 (EFII) or G144-1 (BLK1) - Body ground | Always | 10 kΩ or higher |
| G144-8 (BLK3) or G156-28 (IMI) - Body ground | Always | 10 kΩ or higher |
| G144-7 (BLK2) or G156-29 (IMO) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) or G38-30 (IMI) - Body ground | Always | Below 1 V |
| G26-12 (EFII) or G38-29 (IMO) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) or G144-2 (BLK4) - Body ground | Always | Below 1 V |
| G26-12 (EFII) or G144-1 (BLK1) - Body ground | Always | Below 1 V |
| G144-8 (BLK3) or G38-30 (IMI) - Body ground | Always | Below 1 V |
| G144-7 (BLK2) or G38-29 (IMO) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) or G88-16 (IMI) - Body ground | Always | Below 1 V |
| G26-12 (EFII) or G88-15 (IMO) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) or G146-31 (IMI) - Body ground | Always | Below 1 V |
| G26-12 (EFII) or G146-32 (IMO) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) or G144-2 (BLK4) - Body ground | Always | Below 1 V |
| G26-12 (EFII) or G144-1 (BLK1) - Body ground | Always | Below 1 V |
| G144-8 (BLK3) or G146-31 (IMI) - Body ground | Always | Below 1 V |
| G144-7 (BLK2) or G146-32 (IMO) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) or G148-28 (IMI) - Body ground | Always | Below 1 V |
| G26-12 (EFII) or G148-29 (IMO) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) or G144-2 (BLK4) - Body ground | Always | Below 1 V |
| G26-12 (EFII) or G144-1 (BLK1) - Body ground | Always | Below 1 V |
| G144-8 (BLK3) or G148-28 (IMI) - Body ground | Always | Below 1 V |
| G144-7 (BLK2) or G148-29 (IMO) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) or G154-16 (IMI) - Body ground | Always | Below 1 V |
| G26-12 (EFII) or G154-15 (IMO) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) or G156-28 (IMI) - Body ground | Always | Below 1 V |
| G26-12 (EFII) or G156-29 (IMO) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-13 (EFIO) or G144-2 (BLK4) - Body ground | Always | Below 1 V |
| G26-12 (EFII) or G144-1 (BLK1) - Body ground | Always | Below 1 V |
| G144-8 (BLK3) or G156-28 (IMI) - Body ground | Always | Below 1 V |
| G144-7 (BLK2) or G156-29 (IMO) - Body ground | Always | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the ECM with a new one.
for 1KD-FTV:
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2KD-FTV
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2TR-FE
Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ECM>REMOVAL
for 2TR-FBE
Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>ECM>REMOVAL
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Reregister the ECU - ECM communication ID (Refer to Service Bulletin).
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR
DTC B2799 is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o Blocking System) | B |
| NG (w/ Blocking System) | C |
A
B
C
Temporarily replace the transponder key ECU assembly with a new one (Refer to Service Bulletin).
| Proceed to |
|---|
| NEXT |
NEXT
Reregister the ECU - ECM communication ID (Refer to Service Bulletin).
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR
DTC B2799 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG