Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2012.10
RM1840EF _58 Vehicle Interior _009641 THEFT DETERRENT / KEYLESS ENTRY _0052689 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Security Indicator Light Does not Blink  


DESCRIPTION

When the engine immobiliser system is set, the security indicator light assembly blinks continuously, but does not illuminate if the engine immobiliser system is not set.


WIRING DIAGRAM

B278724
4.594,2.156 4.99,2.354 0.396,0.198 10 false G26 5.229,1.396 5.542,1.594 0.313,0.198 10 false IND 5.01,1.302 5.146,1.5 0.135,0.198 10 false 8 5.219,1.813 5.563,2.01 0.344,0.198 10 false GND 4.948,1.719 5.135,1.917 0.188,0.198 10 false 16 5.229,0.677 5.542,0.875 0.313,0.198 10 false IG 5.021,0.594 5.156,0.792 0.135,0.198 10 false 2 5.208,0.271 5.521,0.469 0.313,0.198 10 false +B 2.302,0.271 3.115,0.469 0.813,0.198 10 false from Battery 4.344,0.417 4.844,0.615 0.5,0.198 10 false ECU-B 3.615,0.417 3.969,0.615 0.354,0.198 10 false DCC 4.427,0.833 4.729,1.031 0.302,0.198 10 false IGN 1.833,0.688 3.708,0.885 1.875,0.198 10 false from Ignition Switch Assembly 5.021,0.177 5.156,0.375 0.135,0.198 10 false 1 3.51,1.302 3.646,1.479 0.135,0.177 10 false 2 1.917,1.302 2.031,1.479 0.115,0.177 10 false 1 2.094,1.302 2.208,1.469 0.115,0.167 10 false E 3.25,1.302 3.448,1.469 0.198,0.167 10 false LP 4.594,2.323 6.698,2.521 2.104,0.198 10 false Transponder Key ECU Assembly 1.615,1.656 1.906,1.813 0.292,0.156 10 false G27 1.615,1.802 3.698,1.979 2.083,0.177 10 false Security Indicator Light Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly, refer to Registration.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK FOR DTC

Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT)

NG

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT)
a.

Check that the security indicator light assembly illuminates when operating it with the Active Test.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DATA LIST / ACTIVE TEST

Immobiliser
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator light ON or OFF The test is possible when the following condition is met:
The key is in the ignition key cylinder.

OK:

Security indicator light assembly can be turned on and off using the intelligent tester.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (ENGINE IMMOBILISER SYSTEM STATUS)

NG

4.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - TRANSPONDER KEY ECU AND BODY GROUND)
3.READ VALUE USING INTELLIGENT TESTER (ENGINE IMMOBILISER SYSTEM STATUS)
a.

Turn the ignition switch off.

HINT:

When using the intelligent tester with the ignition switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds until communication between the intelligent tester and vehicle begins.



b.

Using the intelligent tester, read the Data List.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DATA LIST / ACTIVE TEST

Immobiliser
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Immobiliser Engine immobiliser system status determined by transponder key ECU assembly / Set or Unset Set: Engine immobiliser set (engine start prohibited [no key in ignition key cylinder])Unset: Engine immobiliser unset (engine start permitted [key inserted in ignition key cylinder]) When the engine immobiliser system does not change to the unset state, this item can be used to determine if the cause is the transponder key ECU assembly.

OK:

Set (the key is not inserted in the ignition key cylinder) and Unset (the key is inserted in the ignition key cylinder) appear on the screen according to the key insertion condition.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - TRANSPONDER KEY ECU AND BODY GROUND)
a.

Disconnect the G27 security indicator light assembly connector.


b.

Disconnect the G26 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G27-2 (LP) - G26-8 (IND) Always Below 1 Ω
G27-1 (E) - Body ground Always Below 1 Ω
G27-2 (LP) or G26-8 (IND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE SECURITY INDICATOR LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE SECURITY INDICATOR LIGHT ASSEMBLY
a.

Temporarily replace the security indicator light assembly with a new or normally functioning one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK SECURITY INDICATOR LIGHT ASSEMBLY
6.CHECK SECURITY INDICATOR LIGHT ASSEMBLY
a.

When the immobiliser is set (the ignition switch is off), check that the security indicator light assembly blinks.

OK:

Security indicator light assembly blinks.



Result:
Proceed to
OK
NG



OK

END (SECURITY INDICATOR LIGHT IS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)
a.
B274403
0.302,1.229 0.719,1.552 0.417,0.323 0.583,1.052 0.74,1.052 0.74,1.052 0.969,1.292 true 2.896,1.865 2.667,1.865 2.667,1.865 2.417,1.542 true 0.74,0.677 0.979,0.677 0.979,0.677 1.146,1.26 true 0.042,0.042 0.354,0.24 0.313,0.198 10 false *a 0.563,0.604 0.875,0.802 0.313,0.198 10 false IG 0.375,0.969 0.688,1.167 0.313,0.198 10 false +B 2.927,1.792 3.385,1.99 0.458,0.198 10 false GND 0.385,1.323 0.844,1.521 0.458,0.198 10 false G26
*a Front view of wire harness connector
(to Transponder Key ECU Assembly)


Disconnect the G26 transponder key ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G26-16 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G26-1 (+B) - Body ground Always 11 to 14 V
G26-2 (IG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR