Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2012.10
RM1840EF _58 Vehicle Interior _009641 THEFT DETERRENT / KEYLESS ENTRY _0052688 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the theft warning ECU assembly.

WIRING DIAGRAM

B276315
5.833,0.365 6.104,0.542 0.271,0.177 10 false +B1 5.667,0.26 5.781,0.438 0.115,0.177 10 false 4 5.844,1.417 6,1.594 0.156,0.177 10 false E 5.656,1.344 5.771,1.521 0.115,0.177 10 false 1 5.844,0.906 6.115,1.083 0.271,0.177 10 false +B2 4.688,0.49 5.146,0.667 0.458,0.177 10 false ECU-B 3.719,0.479 4.073,0.656 0.354,0.177 10 false DCC 1.521,0.333 2.333,0.51 0.813,0.177 10 false from Battery 4.167,1.042 4.604,1.219 0.438,0.177 10 false DOOR 5.74,1.948 6.042,2.104 0.302,0.156 10 false G29 5.75,2.104 6.771,2.458 1.021,0.354 10 false Theft Warning ECU Assembly 5.604,0.823 5.781,1 0.177,0.177 10 false 14

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the theft warning ECU assembly, refer to the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(for Built-in Type Door Control Receiver)>REGISTRATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - BATTERY AND BODY GROUND)
a.
B274165
0.24,1.167 0.667,1.521 0.427,0.354 0.948,0.563 1.104,0.563 1.104,0.563 1.26,1.208 true 0.427,0.885 0.594,0.885 0.594,0.885 0.896,1.198 true 2.521,1.198 2.719,0.917 2.719,0.917 2.906,0.917 true 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.313,0.813 0.469,1.01 0.156,0.198 10 false E 0.656,0.49 1.115,0.688 0.458,0.198 10 false +B1 2.948,0.833 3.406,1.031 0.458,0.198 10 false +B2 0.313,1.26 0.771,1.458 0.458,0.198 10 false G29
*a Front view of wire harness connector
(to Theft Warning ECU Assembly)


Disconnect the G29 theft warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G29-1 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G29-4 (+B1) - Body ground Always 11 to 14 V
G29-14 (+B2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR