Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052066 ECD SYSTEM(w/o EGR Cooler) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P0087  Fuel Rail / System Pressure - Too Low  P0190  Fuel Rail Pressure Sensor Circuit  P0192  Fuel Rail Pressure Sensor Circuit Low Input  P0193  Fuel Rail Pressure Sensor Circuit High Input  


DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the suction control valve to regulate the internal pressure so that it reaches the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip. This sensor outputs a voltage in proportion to the internal fuel pressure.

A208460
2.781,0.51 2.938,0.365 2.938,0.365 2.99,0.365 false 3.135,2.208 3.24,2.156 3.24,2.156 3.281,2.156 false 1.948,1.656 2.177,1.656 false 2.229,1.104 2.5,1.104 false 1.406,0.521 0.938,0.635 false 0.063,0.031 1.781,0.333 1.719,0.302 10 false Property of Output Voltage: 1.052,0.385 1.365,0.542 0.313,0.156 10 false 5.00 0.635,0.563 0.948,0.76 0.313,0.198 10 false 4.90 2.219,1.594 2.885,1.948 0.667,0.354 10 false RR2 (Sub) 1.542,1.031 2.24,1.281 0.698,0.25 10 false RR (Main) 1.052,0.635 1.375,0.844 0.323,0.208 10 false 4.44 1.052,0.844 1.385,1.021 0.333,0.177 10 false 3.89 1.052,1.719 1.375,1.885 0.323,0.167 10 false 1.40 1.052,1.917 1.365,2.094 0.313,0.177 10 false 0.85 1.052,2.083 1.375,2.24 0.323,0.156 10 false 0.55 1.24,2.229 1.365,2.385 0.125,0.156 10 false 0 2.938,2.333 3.521,2.563 0.583,0.229 10 false 190000 1.333,2.417 2.656,2.625 1.323,0.208 10 false Fuel Pressure (kPa) 3.323,2.083 4.26,2.333 0.938,0.25 10 false Stores P0192 3.042,0.281 3.948,0.594 0.906,0.313 10 false Stores P0193 0.063,1.115 1.26,1.417 1.198,0.302 10 false Output Voltage (V) 5.208,1.167 5.635,1.438 0.427,0.271 10 false Main 5.24,1.927 5.656,2.177 0.417,0.25 10 false Sub 6.76,1.177 7.073,1.365 0.313,0.188 10 false PR 6.76,1.375 7.073,1.563 0.313,0.188 10 false E2 6.76,1.719 7.115,1.927 0.354,0.208 10 false VCS 6.76,1.927 7.083,2.146 0.323,0.219 10 false PR2 5.927,0.625 6.167,0.813 0.24,0.188 10 false VC 6.365,2.448 6.677,2.635 0.313,0.188 10 false E2S 4.219,0.031 6.729,0.542 2.51,0.51 10 false Internal Structure of the Pressure Sensor (Duplicate Systems):

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0087 Fuel Rail / System Pressure - Too Low Fuel pressure sensor output voltage stays at fixed value for 90 seconds (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

Ran out of fuel

·

Fuel frozen

·

ECM


Comes on DTC stored
P0190 Fuel Rail Pressure Sensor Circuit Fuel pressure sensor output voltage is 0.55 V or less, or 4.9 V or higher for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)


Comes on DTC stored
P0192 Fuel Rail Pressure Sensor Circuit Low Input Fuel pressure sensor output voltage is 0.55 V or less for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)


Comes on DTC stored
P0193 Fuel Rail Pressure Sensor Circuit High Input Fuel pressure sensor output voltage is 4.9 V or higher for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)


Comes on DTC stored

Related Data List
DTC No. Data List
P0087
·

Fuel Press

·

Target Common Rail Pressure


P0190
P0192
P0193

HINT:
·

Check Fuel Press and compare it to Target Common Rail Pressure in the Data List by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Press, Target Common Rail Pressure. Under stable conditions, the difference between Fuel Press and Target Common Rail Pressure is 5000 kPa or less.

·

For more information on the fuel pressure sensor and common rail system, refer to System Description (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>SYSTEM DESCRIPTION).

·

If DTC P0087 is stored, the following symptoms may appear:

·

Black smoke

·

Poor drivability

·

Lack of power

·

Lack of power due to accelerator restriction performed by fail-safe function


·

If DTC P0190, P0192 and/or P0193 is stored, the following symptom may appear:

·

Lack of power due to accelerator restriction performed by fail-safe function


·

If DTC P0190, P0192 and/or P0193 is stored, "Fuel Press" always displays 0 kPa or 200000 kPa.



CONFIRMATION DRIVING PATTERN

P0087
DTC Detection Drive Pattern After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds

P0190, P0192, P0193
DTC Detection Drive Pattern Ignition switch to ON for 1 second

MONITOR DESCRIPTION

P0087 (Fuel pressure sensor output stays at fixed value):
·

Under normal conditions, the internal fuel pressure of the common rail usually fluctuates by 1000 to 2000 kPa (10 to 20 kgf/cm2, 145 to 290 psi) even when driving conditions are constant. This DTC is stored if there is no fluctuation of the fuel pressure. The internal fuel pressure is approximately 25000 to 35000 kPa (255 to 357 kgf/cm2, 3626 to 5076 psi) when idling, and it increases to approximately 28000 to 48000 kPa (286 to 489 kgf/cm2, 4060 to 6960 psi) when running the engine at 3000 rpm.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

·

The diagram below indicates that fuel pressure rises as engine speed increases, but for the malfunction indicated by this DTC, that does not happen.

A175676
5,0.885 5.427,0.563 false 4.698,1.802 4.188,1.438 false 4.698,1.802 4.833,1.802 false 5.427,0.563 5.625,0.563 false 0.063,0.073 1.906,0.281 1.844,0.208 10 false P0087 Malfunction Detection 2.271,0.552 3.229,0.771 0.958,0.219 10 false Fuel Pressure 4.896,1.729 5.563,1.927 0.667,0.198 10 false Abnormal 5.667,0.479 6.25,0.677 0.583,0.198 10 false Normal 2.292,2.167 3.24,2.375 0.948,0.208 10 false Engine Speed 5.229,3.375 5.615,3.542 0.385,0.167 10 false Time



P0190, P0192 and P0193 (Open or short in fuel pressure sensor circuit):

These DTCs are stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short malfunction of the sensor circuit.

If these DTCs are stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


WIRING DIAGRAM

A255063
0.604,3.99 0.927,4.167 0.323,0.177 10 false C16 0.604,4.146 2.021,4.427 1.417,0.281 10 false Fuel Pressure Sensor 6.115,3.969 6.5,4.146 0.385,0.177 10 false ECM 1.698,0.74 1.948,0.917 0.25,0.177 10 false VC 1.688,1.302 1.969,1.479 0.281,0.177 10 false PR 1.708,1.844 1.948,2 0.24,0.156 10 false E2 1.635,2.406 1.969,2.615 0.333,0.208 10 false E2S 1.625,2.958 1.99,3.135 0.365,0.177 10 false PR2 1.615,3.51 1.969,3.729 0.354,0.219 10 false VCS 5.823,0.708 6.073,0.885 0.25,0.177 10 false VC 5.823,1.271 6.24,1.448 0.417,0.177 10 false PCR1 5.823,1.833 6.083,2.052 0.26,0.219 10 false E2 5.823,2.385 6.167,2.563 0.344,0.177 10 false E2S 5.823,2.948 6.281,3.125 0.458,0.177 10 false PCR2 5.823,3.51 6.177,3.688 0.354,0.177 10 false VCS 1.99,0.823 2.146,1 0.156,0.177 10 false 6 1.99,1.385 2.146,1.552 0.156,0.167 10 false 5 1.99,1.938 2.135,2.115 0.146,0.177 10 false 4 2,2.49 2.135,2.646 0.135,0.156 10 false 3 2,3.063 2.146,3.26 0.146,0.198 10 false 2 5.583,3.333 5.729,3.531 0.146,0.198 10 false 2 2,3.625 2.146,3.823 0.146,0.198 10 false 1 5.583,2.208 5.729,2.375 0.146,0.167 10 false 1 5.49,0.729 5.823,0.906 0.333,0.177 10 false C22 5.49,1.302 5.823,1.479 0.333,0.177 10 false C22 5.49,1.854 5.823,2.031 0.333,0.177 10 false C22 5.49,2.406 5.823,2.583 0.333,0.177 10 false C23 5.49,3.531 5.823,3.708 0.333,0.177 10 false C23 5.49,2.969 5.823,3.146 0.333,0.177 10 false C22 5.542,0.531 5.75,0.719 0.208,0.188 10 false 18 5.542,1.104 5.75,1.292 0.208,0.188 10 false 26 5.542,1.656 5.75,1.844 0.208,0.188 10 false 28 5.542,2.771 5.75,2.958 0.208,0.188 10 false 33

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).


HINT:
·

If DTCs relating to different systems which share terminal E2 as their ground are stored, check this ground circuit first.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P0190, P0192 or P0193 is output A
P0087 is output B




A

2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

B

4.REPLACE FUEL PRESSURE SENSOR (COMMON RAIL ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-5 (PR) - C22-26 (PCR1) Always Below 1 Ω
C16-2 (PR2) - C22-33 (PCR2) Always Below 1 Ω
C16-1 (VCS) - C23-2 (VCS) Always Below 1 Ω
C16-6 (VC) - C22-18 (VC) Always Below 1 Ω
C16-4 (E2) - C22-28 (E2) Always Below 1 Ω
C16-3 (E2S) - C23-1 (E2S) Always Below 1 Ω
C16-5 (PR) or C22-26 (PCR1) - Body ground Always 10 kΩ or higher
C16-2 (PR2) or C22-33 (PCR2) - Body ground Always 10 kΩ or higher
C16-1 (VCS) or C23-2 (VCS) - Body ground Always 10 kΩ or higher
C16-6 (VC) or C22-18 (VC) - Body ground Always 10 kΩ or higher
C16-4 (E2) or C22-28 (E2) - Body ground Always 10 kΩ or higher
C16-3 (E2S) or C23-1 (E2S) - Body ground Always 10 kΩ or higher



d.

Reconnect the fuel pressure sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
a.
A204375
0.563,1.135 0.948,1.375 0.385,0.24 1.073,0.781 1.427,1.052 true 1.094,1.615 1.417,1.323 true 2.302,1.635 1.958,1.323 true 1.958,1.021 2.292,0.719 true 0.75,0.667 1.115,0.865 0.365,0.198 10 false VCS 0.625,1.167 0.927,1.354 0.302,0.188 10 false C16 2.344,0.625 2.802,0.823 0.458,0.198 10 false E2S 0.885,1.615 1.104,1.802 0.219,0.188 10 false E2 2.385,1.594 2.604,1.802 0.219,0.208 10 false VC 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Fuel Pressure Sensor)


Disconnect the fuel pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C16-6 (VC) - C16-4 (E2) Ignition switch ON 4.5 to 5.5 V
C16-1 (VCS) - C16-3 (E2S) Ignition switch ON 4.5 to 5.5 V



c.

Reconnect the fuel pressure sensor connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE FUEL PRESSURE SENSOR (COMMON RAIL ASSEMBLY)

NG

7.REPLACE ECM
4.REPLACE FUEL PRESSURE SENSOR (COMMON RAIL ASSEMBLY)
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>2KD-FTV FUEL>COMMON RAIL(w/o DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P0190, P0192 OR P0193)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P0190, P0192 OR P0193)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Let the engine idle for 60 seconds, and then quickly increase the engine speed to 2500 rpm repeatedly for 30 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

f.

Read the DTCs.

Result:
Result Proceed to
P0087, P0190, P0192 or P0193 is output A
No DTC is output B




A

7.REPLACE ECM

B

END

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Let the engine idle for 60 seconds, and then quickly increase the engine speed to 2500 rpm repeatedly for 30 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0087, P0190, P0192 and/or P0193.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.



Result:
Proceed to
NEXT



NEXT

END